How to reduce the failure rate of asphalt mixing plants?

Judging from the situation of highways in our country, asphalt pavement is the most used, which is one of the reasons why asphalt mixing plants have developed so rapidly. Under the situation of rapid economic development, the quality problems of asphalt pavement are gradually increasing, which puts forward higher and higher requirements for the quality of asphalt. It is understood that the primary factor that affects the quality of asphalt is the ratio of raw materials. This is also covered in the introduction of asphalt mixing stations. You can discuss it together.
In order to obtain high-quality asphalt products, in addition to the asphalt mixing equipment meeting the requirements, selecting the appropriate asphalt mixture gradation type is also a top priority. According to my country’s current regulations, the maximum particle size of the asphalt mixture in the upper layer of the highway should not exceed half of the layer thickness; while the maximum particle size of the aggregate in the middle surface layer of asphalt mixture should not exceed two-thirds of the layer thickness; and the asphalt layer should not exceed half of the layer thickness. The maximum nominal aggregate size of the pavement structural layer mixture should not exceed one-third of the layer thickness.
Based on this analysis, if an asphalt surface layer with a certain thickness is selected according to the above specifications, the particle size of the asphalt mixture aggregates will generally be larger, which will inevitably bring insurmountable construction difficulties to the construction of asphalt concrete pavement. After investigation, testing, analysis, and comparison, it can be seen that the lower layer has a wider choice, so the AG-201 gradation type can be used; while the selection of the upper layer mixture type is more difficult, and it is necessary to achieve a reasonable choice of this mix ratio. , on the one hand, we must examine as many aggregate resources as possible, and on the other hand, we must also consider the model of the mixing equipment.
In order to ensure the quality of the project, strict selection and inspection of engineering materials must be carried out. Therefore, the selection and determination of raw materials should be based on the requirements for pavement structure and use quality, combined with the supply of floor materials, and inspection in accordance with the requirements of relevant test procedures, and then Select the best materials so that all technical indicators of the materials meet the specified technical requirements.

The asphalt mixing plant is a complete set of equipment for mass production of asphalt concrete. The whole machine of the equipment consists of multiple systems, such as batching system, drying system, combustion system, powder supply system and dust prevention system. Each system is an important part of the asphalt mixing plant.
The working condition of the combustion system of the asphalt mixing plant has a great impact on the whole system, which is related to the economic efficiency of the whole system, temperature control accuracy and flue gas emission indicators. This article will briefly introduce how to judge the working condition of the combustion system of the asphalt mixing plant.
Generally speaking, due to the complexity of the detection equipment and methods, there are no conditions to achieve in the working process of most asphalt mixing plants. Therefore, it is more convenient to judge the working condition by a series of relatively intuitive factors such as the color, brightness and shape of the flame. This method is very simple and effective.

The basic working principle of the green asphalt mixing plants can be roughly summarized in the following ways:
To put it simply, an asphalt plant is actually a set of equipment that can mix several materials according to a predetermined ratio to form a relatively uniform mixture. It is currently widely used and is very important for the construction of different projects. Its performance Various aspects also have a great impact on the engineering quality of asphalt pavement.
Asphalt mixing plant equipment is usually divided into two structures. The intermittent type is relatively more complex in structure and process. The aggregates need to be screened twice and then measured in batches. The batching accuracy is higher. , the mixing quality is good and can meet different construction requirements. The continuous type has a slightly lower accuracy due to its simple structure and simplified operating procedures.

As a special equipment, standardizing the operating procedures of important production tools of asphalt mixing stations, conducting daily maintenance, regular inspections, eliminating hidden dangers, etc. can effectively ensure the safety and stability of the equipment and prevent equipment from malfunctioning due to misoperation. causing equipment damage. Good maintenance operations can also greatly extend the service life of asphalt mixing plants. Therefore, before daily operation, the asphalt mixing plant must be properly maintained to make the asphalt mixing plant operate better and create wealth.

Asphalt mixing stations play an important role in road construction. This article starts from the site selection, commissioning, and acceptance of the asphalt mixing plant, and elaborates on comprehensive and reasonable planning to avoid disturbing the normal construction order.

Speaking of asphalt mixing plants, we are not unfamiliar with them. This is a unit equipment specially used for asphalt mixing. In fact, what we really lack understanding of is its gas system. Even the accumulated failures that often occur in the gas system of asphalt mixing plants are not very clear. Facts have proved that only by properly maintaining the various systems of the equipment can efficient production and good benefits be achieved.
The following are four types of gas system failures that often occur in asphalt mixing plants. Let’s analyze the causes of the problems behind the failures one by one.

Modified Bitumen

How should the working efficiency of asphalt mixing plant be improved? Let’s take a brief look.
1. Parameter setting. When using asphalt mixing plant to produce asphalt, the temperature of the hot pot can be observed through the temperature controller, but there is a certain difference between the information displayed by the temperature controller and the actual temperature. The generation of this error does not have much impact on the processing quality. If the information entered by the staff when setting the temperature is accurate, there will be no problems with the produced asphalt. It can be seen that the setting of parameters requires more attention.
2. Pay attention to avoid moisture in the equipment. When transporting and storing the asphalt mixing plant, pay attention to avoid moisture in the equipment, because there are many circuit devices inside it, if moisture, it may cause quality problems or even damage. This is also an important point to consider to improve production efficiency.
3. When installing and using the asphalt mixing plant, pay attention to whether the equipment is grounded. Before starting the equipment, it must be preheated in time so that the temperature standard can be reached within a shorter time range, so as to enter the normal asphalt production process.

Asphalt concrete mixing equipment generally uses conveyor belt conveyors to transport cold materials. Its main advantages are large conveying capacity, continuous operation, simple equipment structure and automatic control. However, belt deviation is a common fault, which directly affects the drying operation of the drying drum and also affects the production efficiency of the mixing equipment. Therefore, it is very important for the asphalt mixing station to solve the belt deviation problem at the operation site of the asphalt concrete mixing equipment.

What should I do when the reversing valve in the asphalt mixing plant fails? The editor has a trick:
1. The reversing valve cannot be reversed or the reversing action is slow, which is generally caused by poor lubrication, stuck or damaged springs, oil or impurities stuck in the sliding parts. In this regard, you should first check whether the oil mist is working normally; whether the viscosity of the lubricating oil is appropriate. If necessary, the lubricating oil should be replaced, the sliding part of the reversing valve should be cleaned, or the spring and reversing valve should be replaced.

In the process of building and maintaining roads, road asphalt materials are an indispensable part. Asphalt, as a binder, can be used for various surface treatments, such as roads, parking lots, airport runways, etc. However, choosing the right road asphalt material for you is not an easy task. In this article, we will discuss how to choose the road asphalt material that best suits your needs.
1. Understand the types of road asphalt materials
First, we need to understand what road asphalt materials are available. According to the material properties and their application areas, they can generally be divided into the following categories:
(1) Conventional petroleum asphalt: It is extracted from petroleum and has strong durability and viscosity. It is often used in the surface layer of highways, urban trunk roads, etc.
(2) Modular asphalt: It is obtained by mixing conventional petroleum asphalt with other materials. It has better toughness and crack resistance. It is usually used for viaducts, large airport runways, etc.
(3) High temperature stabilizer modified asphalt: By adding high temperature stabilizers, the high temperature resistance of asphalt is increased. It is usually used in high temperature areas, such as roads in southern provinces.
(4) Polymer modified asphalt: By adding polymers, the toughness, crack resistance and durability of asphalt are increased. It is usually used in large parking lots, factory areas, etc.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

Any kind of mechanical equipment must go through precise design, testing and other processes before it can be manufactured, and the same is true for asphalt mixing stations. According to the survey, the following stages are necessary for any asphalt mixing plant.
First of all, the main technical parameters of the product to be designed must be determined according to market needs, so construction market research, data analysis and other links are indispensable. Secondly, the ideal working principle and the plan to realize this principle will be determined through innovative conception and optimization screening. , a schematic diagram of the overall design scheme should also be given.

Asphalt mixing plant is a complete set of equipment composed of many systems. It is widely used in the current society. Its components include batching system, drying system, combustion system, hot material lifting, weighing and mixing system and control system.
In the process of asphalt mixing, heating is an indispensable link, because there must be a system for heating in the asphalt mixing station, but the system generally fails for various reasons. So how should the heating system of the asphalt mixing station be improved? This article will briefly explain this issue.
Generally speaking, when the asphalt mixing station is running under low temperature conditions, the asphalt circulation pump and spray pump cannot operate normally, which will cause the asphalt in the asphalt scale to solidify, and then the asphalt mixing station cannot be produced. Therefore, the asphalt mixing station needs a heating system during operation.

In highway construction, asphalt mixing station plays a vital role. As a kind of equipment integrating intelligence, high efficiency and environmental protection, asphalt mixing station provides strong support for improving the quality of highway construction. This article will introduce the relevant knowledge of asphalt mixing station in detail to help readers understand this key equipment.
Asphalt mixing station is a kind of equipment specially used for producing asphalt concrete, which is widely used in highway, municipal road, bridge and other engineering construction. Asphalt concrete is a kind of building material mixed with asphalt, gravel, sand and other materials. It has the characteristics of strong durability and good compressive resistance. It is an ideal material for highway construction.
2. Features
Intelligence: Asphalt mixing station is equipped with advanced control system and sensor, which can realize automatic production, reduce manpower input and improve production efficiency.
Environmental protection: Asphalt mixing station adopts closed design to reduce dust pollution, and is equipped with noise reduction facilities to reduce noise pollution.
Efficiency: Asphalt mixing station has high production capacity and can produce a large amount of asphalt concrete in a short time to meet the needs of engineering construction.
3. Function
Provide asphalt concrete: The main function of asphalt mixing station is to produce asphalt concrete and provide necessary building materials for highway construction.
Improve highway quality: By using asphalt concrete, the smoothness, compressive strength and durability of the highway can be improved, thereby improving the quality of the highway.

Asphalt flue gas treatment methods, their principles and characteristics, and an asphalt flue gas environmental protection treatment plan based on the actual asphalt flue gas problems faced by the unit.

1. Basic situation
My unit’s mixing plant is equipped with a 4000-type asphalt mixing plant. During daily production of the asphalt mixing plant, a large amount of asphalt smoke will be emitted from the mixing pot discharge port. This smoke not only has an unpleasant smell, but also contains A large number of compounds that are harmful to the human body, such as benzopyrene, benzanthracene, carbazole and other polycyclic aromatic hydrocarbons, mostly have carcinogenic risks. Smoke overflow will cause pollution to the surrounding atmospheric environment and affect the personal health of workers. Although the overflow port of the mixing station is equipped with a dust retaining wall, the fine dust is seriously raised, and the cold material belt conveyor is dusty. In order to protect the environment, reduce pollution, and reduce cost investment, based on full research and absorption of technology in the same industry, and combined with the actual situation of asphalt mixing, we are planning to install asphalt mixing bag dust collectors to the flue at the discharge port of the mixing pot to control asphalt fumes. Gas is processed. The dust removal efficiency of the bag dust collector can reach 97%~99%, and the dust-containing gas can be purified to a level of 50mg/Nm3.

When using an asphalt mixing plant, first of all, it needs to have good stability. If it does not have good stability, then the asphalt mixing plant will not be able to meet the requirements of the project in terms of requirements or mass production. For road construction, the measurement requirements of asphalt concrete are relatively strict and precise. Only qualified asphalt concrete can make the quality of road construction meet the actual requirements. Therefore, the stability of the asphalt mixing plant is very important.
Secondly, the requirements for the asphalt mixing plant when in use are that the equipment should be as simple as possible on the basis of having all the required functions, and the overall operation should be reduced as much as possible. This can save a lot of manpower input during operation and save corresponding costs. Although it is simple, it does not mean that the technological content of the asphalt mixing plant needs to be reduced.
The above are the requirements that the asphalt mixing plant needs to meet when in use, because if each equipment wants its working effect to achieve the expected appearance, the equipment itself needs to have corresponding conditions. It must be a qualified and convenient equipment to ensure the efficiency and quality of the work.

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.

After use, asphalt mixing equipment needs to be disassembled, cleaned, and maintained before it can be saved for next use. Not only is the disassembly process of the equipment important, but the previous preparation work also has a greater impact, so it cannot be neglected. Please pay attention to the detailed introduction below for specific content.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

The asphalt mixing plant contains multiple different systems with different functions. The drying system is one of them. Its main function is to heat and dry the materials to reach the temperature required for the process. In order to successfully achieve this goal, the drying system must provide a certain amount of heat.

Asphalt mixing stations are constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing station is not damaged. Although construction details are critical, the key skills of asphalt mixing station construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing station construction range should be removed, and the site elevation should be kept dry and flat to meet the design requirements. If the surface is too soft, the foundation should be reinforced to prevent the construction machinery from losing stability and ensure that the pile frame is vertical.
Then the on-site construction machinery should be inspected to ensure that the machinery is intact and assembled and tested under the premise of meeting the requirements. To ensure the verticality of the asphalt mixing plant, the deviation of the gantry guide and the mixing shaft from the verticality of the ground shall not exceed 1.0%. Asphalt mixer manufacturer.

It is inevitable that the asphalt mixing plant will have insufficient pumping force during use. In fact, during the construction process, as long as the asphalt mixing station is operated in accordance with regulations, and the accessories are cleaned and replaced in time, the asphalt mixing plant will generally not have insufficient pumping force. Now the editor of the asphalt mixing station manufacturer briefly introduces the common solutions to insufficient pumping force of asphalt mixing plant as follows.

Asphalt damage avoidance mechanism in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

Construction safety has always been a major issue, and we cannot let any safety hazard go unnoticed. Especially the use of equipment at the construction site. Asphalt mixing stations are prone to failure. Strengthening the maintenance of this equipment is essential to ensure safe construction at the construction site, improve equipment integrity, reduce equipment failures, and ensure the quality of concrete. The role of neglect.
The composition of the asphalt mixing plant is relatively complex, so during maintenance, classified maintenance should be carried out according to the usage and functions of different parts. Maintenance content can be divided into tank maintenance, winch system maintenance and adjustment, stroke limiter adjustment and maintenance, wire rope and pulley maintenance, lifting hopper maintenance, track and track bracket maintenance, etc.

In the 21st century, with the booming development of modern engineering construction, complex integrated supporting equipment has been invested in large quantities. Its complex process and more independent operating components have relatively high requirements for the performance of its equipment control system. The application of PLC in asphalt mixing station realizes the control of the entire process of asphalt mixing station, which facilitates the construction of modern engineering construction. Therefore, this article discusses and analyzes the application of PLC in asphalt mixing station, which has certain economic value and practical significance.

The asphalt mixing plant is constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing plant is not damaged. Although the construction details are critical, the key skills of the asphalt mixing plant construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing plant construction range should be removed, and the dry and flat site elevation should be kept to meet the design requirements. If the ground surface is too soft, the foundation should be reinforced to prevent the construction machinery from becoming unstable and to ensure that the pile frame is vertical.

The site selection of the asphalt mixing station should follow three principles. Let’s take a look:
1. When selecting the site for the asphalt mixing station in the early stage of construction, the construction party should pay attention to the line direction of the construction site, because the line direction of the construction site will directly affect the quality of the mixed asphalt. Asphalt is an important material used for road and engineering construction. If the quality is poor, it will inevitably have a serious impact on the quality and safety of the entire project. Therefore, when selecting the site, it must be considered in many aspects, and meet the on-site requirements, and confirm the location of the mixing station according to the drawings.
2. Secondly, it is necessary to have a full understanding and grasp of the basic elements of the asphalt mixing station construction, such as whether water and electricity can be supplied normally, or whether the size of the land is sufficient to build an asphalt mixing station.
3. Since the use of asphalt mixing stations belongs to mechanized construction, there will inevitably be dust, noise and other pollution problems during the operation. It can be seen that when selecting the site, it must be kept as far away as possible from residential areas, schools or farms to avoid a greater impact on the surrounding environment.

Asphalt mixing plant is a relatively important complete set of equipment in people’s lives. There are many components of this equipment, such as grading machine, vibrating screen, belt feeder, powder conveyor, elevator and other parts. Plug valve is one of them, so what is the specific role of plug valve in asphalt mixing plant? This article will give a brief introduction.
The plug valve is first of all a closure or plunger-shaped rotary valve. Generally, it is necessary to rotate 90 degrees to make the channel opening on the valve plug the same as that on the valve body, or to split it to play the role of opening or closing. The shape of the plug valve in the asphalt mixing plant is generally cylindrical or conical.