Asphalt mixing plants: an indispensable role in assisting road construction

We know that the first priority in production is to ensure safety. In the process of operating equipment, staff must always pay attention to using the correct operating methods. Regarding the asphalt mixing plant, it is used to produce asphalt mixtures, modified asphalt mixtures, and colored asphalt mixtures to meet the needs of highways, graded highways, municipal roads, airports, etc.

The hydraulic reversing valve of asphalt mixing plants is generally not prone to failure, but occasionally there may be untimely phase change, gas leakage, electromagnetic induction pilot valve, etc., and the corresponding fault causes and treatment methods are naturally different.
If the hydraulic reversing valve does not change phase in time, it is mostly caused by poor finish, spring stuck or damaged, oil stains or residue stuck in the drag part, etc. It is necessary to check the condition of the pneumatic triplex and the viscosity of the grease. If necessary, the grease or other parts can be replaced.
During long-term use, the hydraulic reversing valve of the asphalt mixing plant is prone to damage to the valve core sealing ring, valve seat and high-pressure gate valve, causing gas leakage in the valve. At this time, the sealing ring, valve seat and high-pressure gate valve should be replaced, or the hydraulic reversing valve should be replaced in time.
Therefore, in order to more effectively reduce the equipment failure rate of the asphalt mixing plant, it is also necessary to pay attention to the maintenance of machinery and parts.

Judging from the situation of highways in our country, asphalt pavement is the most used, which is one of the reasons why asphalt mixing plants have developed so rapidly. Under the situation of rapid economic development, the quality problems of asphalt pavement are gradually increasing, which puts forward higher and higher requirements for the quality of asphalt. It is understood that the primary factor that affects the quality of asphalt is the ratio of raw materials. This is also covered in the introduction of asphalt mixing stations. You can discuss it together.
In order to obtain high-quality asphalt products, in addition to the asphalt mixing equipment meeting the requirements, selecting the appropriate asphalt mixture gradation type is also a top priority. According to my country’s current regulations, the maximum particle size of the asphalt mixture in the upper layer of the highway should not exceed half of the layer thickness; while the maximum particle size of the aggregate in the middle surface layer of asphalt mixture should not exceed two-thirds of the layer thickness; and the asphalt layer should not exceed half of the layer thickness. The maximum nominal aggregate size of the pavement structural layer mixture should not exceed one-third of the layer thickness.
Based on this analysis, if an asphalt surface layer with a certain thickness is selected according to the above specifications, the particle size of the asphalt mixture aggregates will generally be larger, which will inevitably bring insurmountable construction difficulties to the construction of asphalt concrete pavement. After investigation, testing, analysis, and comparison, it can be seen that the lower layer has a wider choice, so the AG-201 gradation type can be used; while the selection of the upper layer mixture type is more difficult, and it is necessary to achieve a reasonable choice of this mix ratio. , on the one hand, we must examine as many aggregate resources as possible, and on the other hand, we must also consider the model of the mixing equipment.
In order to ensure the quality of the project, strict selection and inspection of engineering materials must be carried out. Therefore, the selection and determination of raw materials should be based on the requirements for pavement structure and use quality, combined with the supply of floor materials, and inspection in accordance with the requirements of relevant test procedures, and then Select the best materials so that all technical indicators of the materials meet the specified technical requirements.

Never stop, escorting the quality of road construction
Inheriting decades of technical accumulation, asphalt mixing station has become an indispensable part of building and maintaining high-level roads. This seemingly ordinary device carries the important mission of ensuring road safety and improving driving experience. As the core technology of modern road engineering construction, asphalt mixing station goes all out to continuously strive for a better, safer and more efficient travel environment.
Fast drive, tenacious progress
Asphalt mixing station plays a role in road engineering. It uses mature technology and processes to ensure the smooth progress of road construction with efficient mixing capacity and stable production quality. From conveying raw materials to the precise proportion of oil and aggregates, to the uniform mixing of the final product, the asphalt mixing station, with its professional working attitude, ensures the quality and stability of road materials, and provides a solid foundation for the construction of high-standard road projects.
Innovation leads, environmental protection takes the lead
Asphalt mixing station plays an important role in promoting sustainable development. Faced with increasingly urgent environmental protection requirements, mixing stations continue to innovate technology, improve production efficiency, and also pay attention to environmental protection responsibilities. By introducing advanced dust removal and purification devices, intelligent equipment control systems and combustion equipment, the asphalt mixing station effectively reduces environmental pollution and makes positive contributions to protecting the surrounding ecological environment.

Asphalt mixing plant refers to a complete set of equipment used for batch production of asphalt concrete. Its main function is to produce asphalt mixture, colored asphalt mixture, etc., and has been widely used in road construction. However, during the production process of asphalt mixture, pollutants such as noise, dust, and asphalt smoke will be produced, seriously polluting the environment and threatening the health of workers. Therefore, under the current background of building a resource-saving and environment-friendly society in our country, it is very important to save energy and reduce consumption during the use of asphalt mixing plants. The following article mainly starts from the three factors that affect the asphalt mixing plant, and explores the energy saving and consumption reduction measures of the asphalt mixing plant, aiming to reduce the cost of asphalt production and improve the efficiency of the asphalt plant.

When inspecting the asphalt mixing plant, it was found that the asphalt in the pipeline solidified because the temperature of the asphalt transportation pipeline did not meet the requirements. Analysis believes that the reasons for this result are that the high-level oil tank of the heat transfer oil is too low, resulting in poor circulation of the heat transfer oil; the second is that the inner tube of the double-layer pipe is eccentric; the third is that the heat transfer oil pipeline is too long; and the fourth is that the heat transfer oil pipeline is not insulated measure.

Emulsified asphalt equipment plays an important role in road construction, and its production quality will directly affect the quality of facilities such as roads. In order to operate it better, we need to pay special attention to the following four points when applying emulsified asphalt equipment:
1. Before spraying, the emulsified asphalt equipment must check whether the position of each valve is correct. The hot asphalt added to the emulsified asphalt equipment must reach an operating temperature of 160~180℃. For long-distance transportation or long working time, a heating device can be used for insulation, but it cannot be used as an oil melting furnace.
2. When the asphalt in the emulsified asphalt equipment is heated by a burner, the asphalt height must exceed the upper plane of the combustion chamber, otherwise the combustion chamber will be burned.
3. The emulsified asphalt equipment cannot be filled too full, and the fuel filler cap must be closed tightly to prevent asphalt from overflowing during transportation.
4. This vehicle has two front and rear control consoles. When using the front control console, the switch must be turned to the front control. At this time, the rear control console can only control the lifting and lowering of the nozzle.
I believe that through the above description, everyone will be more comfortable when using emulsified asphalt equipment in the future. As for the relevant operating matters of the equipment, I will introduce them to you here today. If you want to know more information, please pay attention to the next explanation.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

Asphalt mixing plant is a relatively important complete set of equipment in people’s lives. There are many components of this equipment, such as grading machine, vibrating screen, belt feeder, powder conveyor, elevator and other parts. Plug valve is one of them, so what is the specific role of plug valve in asphalt mixing plant? This article will give a brief introduction.
The plug valve is first of all a closure or plunger-shaped rotary valve. Generally, it is necessary to rotate 90 degrees to make the channel opening on the valve plug the same as that on the valve body, or to split it to play the role of opening or closing. The shape of the plug valve in the asphalt mixing plant is generally cylindrical or conical.

The site selection of the asphalt mixing station should follow three principles. Let’s take a look:
1. When selecting the site for the asphalt mixing station in the early stage of construction, the construction party should pay attention to the line direction of the construction site, because the line direction of the construction site will directly affect the quality of the mixed asphalt. Asphalt is an important material used for road and engineering construction. If the quality is poor, it will inevitably have a serious impact on the quality and safety of the entire project. Therefore, when selecting the site, it must be considered in many aspects, and meet the on-site requirements, and confirm the location of the mixing station according to the drawings.
2. Secondly, it is necessary to have a full understanding and grasp of the basic elements of the asphalt mixing station construction, such as whether water and electricity can be supplied normally, or whether the size of the land is sufficient to build an asphalt mixing station.
3. Since the use of asphalt mixing stations belongs to mechanized construction, there will inevitably be dust, noise and other pollution problems during the operation. It can be seen that when selecting the site, it must be kept as far away as possible from residential areas, schools or farms to avoid a greater impact on the surrounding environment.

At present, the production efficiency of asphalt mixing plants in my country’s asphalt construction is far lower than the theoretical efficiency at the time of design. The low efficiency of organic waste gas treatment will not only delay the construction process and cause a waste of resources, but also the quality of the construction will not be very good. guarantee. In the construction of asphalt pavement, the main reasons for the low production efficiency of the asphalt plant are insufficient supply of mixture, resulting in loss of continuity of construction, improper equipment parameter settings, excessive overflow and other problems. Effective measures must be taken to deal with these problems, and ultimately improve production efficiency and ensure construction quality.

Main uses of asphalt mixing plant
Asphalt mixing plant, also called asphalt concrete mixing plant, can produce asphalt mixture, modified asphalt mixture, and colorful asphalt mixture, fully meeting the needs of constructing expressways, graded highways, municipal roads, airports, ports, etc.
The overall composition of asphalt mixing plant
Asphalt mixing equipment mainly consists of batching system, drying system, incineration system, hot material improvement, vibrating screen, hot material storage bin, weighing mixing system, asphalt supply system, powder supply system, dust removal system, product silo and control system, etc. Some composition.

1. Causes of overflow
The main causes of spillage are:
1) Mixing materials in cold silo. Cold material warehouses generally have 5 or 4 warehouses. Each warehouse is required to contain pellets of a certain specification. If cold materials of different specifications are mixed or mistakenly loaded during the loading process, it will cause certain occurrences in a certain period of time. The shortage of pellets of one specification and the overflow of pellets of another specification can easily destroy the supply balance between hot and cold silos.

For road construction machinery, the following is mainly about the asphalt mixer in road construction machinery equipment. Because it is the key product of Wuxi road construction machinery manufacturers, it is necessary to carry out comprehensive training and mastery, so as to ensure meticulousness and practicality, and not ignore any knowledge points.
1. In road construction machinery, is there any difference between asphalt mixing equipment and asphalt concrete mixing equipment?
The answer given by Sinoroader Group manufacturer to this question is no, that is, there is no difference between asphalt mixing equipment and asphalt concrete mixing equipment. They refer to the same type of equipment, but they are different in name. It can be said that they are two names for the same type of equipment, and there is no difference in essence.
2. During the operation of the asphalt mixer, there is a sound in the mixing pot. What’s the matter?
In the view of Sinoroader Group, there are two answers to this question. One is that the mixer arm on the asphalt mixer is not good or damaged. The second is that the wear-resistant lining in the mixer is damaged, which leads to this problem.
3. What are the dust removal devices in the asphalt mixing equipment?
In the asphalt mixing equipment, for its dust removal device, Sinoroader Group believes that the key is to use the dry ash removal method, because it can facilitate the collection of raw materials. In terms of its dust removal equipment type, there are filter dust removal equipment, centrifugal fan dust removal equipment and force dust removal equipment, etc., which can all be used well.
For the asphalt mixer and asphalt mixing equipment in road construction machinery, I believe that through the practical discussion of the above relevant content, everyone can master it well and master it, so that in practice, they can have new gains and benefit a lot from it.

The core of the asphalt mixing plant is its electronic control system. If it has problems, it will cause a lot of trouble to use. However, in actual use, the electronic control system in the asphalt mixing plant will inevitably encounter some problems and failures. How to solve it at this time?
If only the instrument display of the electronic control system of the asphalt mixing plant is inaccurate, it means that the weighing system may be affected by external forces; or the drift error of the sensor causes the weighing zero position or weighing interval to change; it may also be caused by sensor damage.

Due to certain restrictions on the current development status and conditions, the profits of the domestic asphalt pavement construction industry are getting lower and lower. Therefore, in the process of using asphalt mixing plants for production, on the one hand, the quality of the products and customer requirements must be ensured. , on the other hand, it is necessary to reduce production costs. Therefore, cost management is very important, and refined management should be implemented in this regard.
First, for device management. Since equipment is the foundation and key of production, in the cost management of asphalt mixing stations, the management of equipment plays an important role in reducing costs. Only by managing the equipment well can the normal working status be ensured, which provides the necessary guarantee for the smooth progress of the project. In fact, in today’s highway projects, equipment costs account for a large part of the cost and profit. The huge profits after the construction of a highway will be greatly affected by the management of materials and equipment.

Asphalt damage avoidance mechanism in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

Due to raw materials or usage, asphalt mixing plants will be subject to a certain degree of wear or other failures during daily use. If they are not controlled or repaired in time, the problem will be further exacerbated. For asphalt mixing plants, what are the ways to prevent wear and failure?
If the asphalt mixing plant is not treated in time after being worn, it may corrode once it is in contact with air, rainwater, etc. for a long time. If the parts of the asphalt mixing plant are severely corroded, the service life and normal operation of the entire equipment will be affected.

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

The mobile forced asphalt mixing equipment adopts intermittent drying cylinder, double forced mixer, the main machine can be towed, small footprint, short installation cycle, convenient operation and maintenance, good stability, high degree of automation, high degree of standardization, and high quality of finished products, and the technology of continuous improvement. The mobile forced asphalt mixing plant is suitable for high-grade road asphalt paving and maintenance.
1. The combined structure of the drum dryer and the batching machine is installed on a movable bracket for easy movement.
2. The asphalt mixing plant is equipped with a double horizontal shaft to boil the aggregate and ensure uniform mixing.
3. In the densely arranged hanging barrels, the hot aggregate rises vertically. This lifting tool is easy to use and reliable.
4. For accurate weighing of aggregates, asphalt and powder ore, a measuring scale is used, which contains a weighing sensor for electronic measurement.
5. The movement of the power material follows a closed spiral path, which ensures little material loss and provides safe transfer.
6. On the cyclone burner, high-pressure oil is sprayed out and quickly atomized. In the combustion chamber, the material is fed in a spiral manner and automatically ignited by the oil mist, which ensures combustion efficiency. The cylindrical barrel of the burner is separated from the burner head. The furnace cavity can be pushed in and pulled out, which is convenient for replacing the damaged side column bricks inside the burner. The entire burner has a large heat capacity and high thermal strength. This is cost-effectiveness.

Asphalt (composition: asphaltenes and resin) tanks are divided into: intermittent and continuous functions according to the production process: initial batching of aggregates, heating and drying, screening and measurement; heating and insulation of asphalt (composition: asphaltene and resin) , transportation and measurement; transportation and measurement of filler; uniformly mix the measured aggregate, asphalt (composition: asphaltene and resin), and filler into a finished product of a certain temperature.

The quality of asphalt mixture directly determines the quality of asphalt pavement engineering. This article discusses the key points of supervision of ordinary highway asphalt plants in order to better monitor the quality of asphalt mixture.

1: The site should be located on higher ground and away from residential areas and densely populated areas.
Because part of the equipment of the mixing station is installed below the ground, in order to avoid continuous rainfall. The equipment will suffer disaster, and the changing aggregate moisture content will affect the concrete quality. Quality accidents are prone to occur. Therefore, during site construction, attention should be paid to the construction of drainage pipelines and sand and gravel quarries. With the rapid development of cities. With the continuous expansion of urban scale, environmental protection requirements will become more and more stringent. Urban roads prohibit gravel vehicles from passing, so concrete mixing plants should be built far away from urban areas.

The basic working principle of the green asphalt mixing plants can be roughly summarized in the following ways:
To put it simply, an asphalt plant is actually a set of equipment that can mix several materials according to a predetermined ratio to form a relatively uniform mixture. It is currently widely used and is very important for the construction of different projects. Its performance Various aspects also have a great impact on the engineering quality of asphalt pavement.
Asphalt mixing plant equipment is usually divided into two structures. The intermittent type is relatively more complex in structure and process. The aggregates need to be screened twice and then measured in batches. The batching accuracy is higher. , the mixing quality is good and can meet different construction requirements. The continuous type has a slightly lower accuracy due to its simple structure and simplified operating procedures.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

The quality of the asphalt mixing plant will be a key factor affecting the quality of the project. After reviewing relevant materials related to the production and construction of asphalt concrete, we summarized some cases of failures in asphalt concrete mixing stations during construction and analyzed the reasons.
1. Unstable output and low production efficiency of asphalt mixing plants
(1) Improper proportioning. The mix ratio of asphalt concrete is divided into target mix ratio and production mix ratio. Among them, the target mix ratio controls the cold material transportation ratio of sand and gravel materials, and the production mix ratio is the mixing ratio of various types of sand and stone materials in the finished asphalt concrete materials specified in the design. The production mix ratio is determined by the laboratory, which directly determines the off-site grading standard of the finished asphalt concrete. The target mix ratio is set to further ensure the production mix ratio, and can be adjusted appropriately during production according to the actual situation. When the target mix ratio or the production mix ratio is not appropriate, the stones stored in each measurement of the asphalt mixing station will be disproportionate, with some overflowing and some other materials, unable to be weighed in time, and the mixing cylinder will be idling, resulting in reduced output.