Let’s take a detailed look at the functions and uses of slurry sealers

Precautions for checking emulsified asphalt equipment
Sinoroader emulsified asphalt pavement engineering common equipment, now has gradually been widely used.
We all know that before any equipment is used, the equipment should be preliminarily inspected to check whether the installation is normal, and then put into use. The use of modified asphalt modified asphalt production equipment can also extend the peak season. The modified asphalt and stone water machine can be mixed with wet stone to form a continuous film under the surface conditions of low-temperature asphalt and stone. The viscosity of the asphalt is low and the viscosity of the emulsified asphalt is low. Wet film below 10 degrees.

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

Slurry sealers are important equipment for road maintenance and repair. They are mainly used to pour durable asphalt mixtures on old roads to form a new protective layer. This equipment can be constructed according to the surface texture of the road surface, so that the cracks in the surface layer are isolated from water and air, effectively preventing the road surface from aging further.
The working principle of the slurry sealer is to mix materials such as aggregate, emulsified asphalt and additives into slurry, and then evenly lay it on the road surface. The slurry formed after the mixture of these materials has good waterproof and skid resistance, which can significantly improve the service life of the road surface and driving safety.

With the rapid development of highway construction and the increase in demand for asphalt, barreled bitumen has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported bitumen used in high-grade highways is in barrel form, which requires an bitumen melter equipment with fast melting speed, clean debarreling, and prevention of asphalt aging.
The upper part of the debarreler of the bitumen melter equipment is hotter, and each barrel is directly heated by the heat transfer oil coil. The barrel wall directly bears the heat radiation of the heating coil. The asphalt is cleanly and sensitively debarreled, and there will be no waste of asphalt hanging barrels. According to the principle of layered heating, four-layer heating technology is adopted, with single inlet and single outlet of heat transfer oil, and high thermal efficiency of heating; at the same time, the waste heat of combustion exhaust gas is used for secondary heating, and power is effectively used; the debarreler body is insulated with high-quality rock wool material. It is suitable for various types of imported and domestic barrels, and the deformation of asphalt barrels will not affect production.

Asphalt anti-sticking release agent is a product used in the construction of hot asphalt mixture to solve the asphalt anti-sticking problem. It is used to replace diesel and vegetable oil! There are all kinds of things about the effect of asphalt anti-sticking release agent. How to use asphalt anti-sticking release agent?
Before use, stir the release agent evenly, spray or apply the original liquid evenly on the surface of construction equipment such as rubber-wheeled rollers, transport carriages, paver hoppers, ironing plates, etc.; or add water to the roller water tank after dilution, stir evenly and spray automatically for use.
When preparing to start construction, when the roller tires are cool or the temperature is low, you should first apply the roller tires with the release agent original liquid, and then start rolling. At the beginning, you need to apply more release agent. After the temperature of the tires rises, you can apply it normally or less. If you use intermittent spraying of release agent, you should spray more frequently at the beginning of construction.
When adding water, we recommend a ratio of 10-15 times. It will be better to use 10 times the water ratio. If you think the cost is high and want to add more water, it is also possible, but try to use less than 15 times the water ratio. If it is modified asphalt, it is recommended to use less than 8 times, and 7 times the water ratio is recommended.

Due to the incorporation of a certain proportion of water into the slurry sealing mixture, it is easy to evaporate in the air. After the water is evaporated, it will become dry and hardened. Therefore, after the slurry is formed, it not only looks very similar to fine-grained asphalt concrete, but does not affect the visual appearance of the road. It also has the same technical properties as fine-grained concrete in terms of wear resistance, anti-skid, waterproofing, and smoothness. Slurry seal technology is used in highway pavement maintenance because of its simple construction technology, short construction period, low cost, high quality, wide application, strong adaptability, etc. It is an asphalt with both economy and high efficiency. Pavement maintenance technology is worthy of application and promotion.

There are certain standards for the composition and mix ratio of micro-surfacing, and a wide range of materials are used, including polymer-modified emulsified asphalt, various aggregates, cement, water, additives, etc. Raw material quality has a significant impact on microsurfacing performance, so understanding the performance of each component and the key factors that influence its performance is critical to ensuring the quality of your microsurfacing mix.

Bitumen melter equipment plays an important role in highway construction, but traditional heating methods have problems such as high energy consumption and low efficiency. This article introduces a new type of bitumen melting plant, which uses electric heating technology and has the advantages of energy saving, environmental protection and environmental protection. The working principle of this equipment is to heat the bitumen through the heat generated by the resistance wire, and then automatically adjust the temperature and flow rate through the control system to achieve the best melting effect.

There are many types of emulsified asphalt (composition: asphaltene and resin) equipment. Emulsified asphalt (composition: asphaltene and resin) equipment can be divided into intermittent operation type, semi-continuous operation type, and Continuing the three operating types, what is the knowledge about different types of emulsified asphalt equipment?

After the emulsified asphalt equipment has been used for a long time, it needs maintenance. There are several points to note when adjusting the emulsified asphalt equipment:
1. During use, regular maintenance should be carried out as appropriate according to the processing materials;
2. For the maintenance and use of the motor, please refer to the motor instruction manual;
3. Most of the random spare parts are national standard and department standard parts, which are purchased all over the country;
4. The colloid mill is a high-precision machine with a line speed of up to 20m/second and a very small grinding disc gap. After overhaul, the coaxiality error between the housing and the main shaft must be corrected with a dial indicator to ≤0.05mm;
5. When repairing the machine, it is not allowed to be directly knocked with an iron bell during the disassembly, reassembly and adjustment process. Use a wooden hammer or a wooden block to knock gently to avoid damaging the parts;
6. The seals of this machine are divided into static and dynamic seals. The static seal uses an O-type rubber ring and the dynamic seal uses a hard mechanical combined seal. If the hard sealing surface is scratched, it should be repaired by grinding on flat glass or flat castings immediately. The grinding material should be ≥200# silicon carbide grinding paste. If the seal is damaged or cracked seriously, please replace it immediately.

Emulsified asphalt is an emulsion that disperses asphalt into the water phase to form a liquid at room temperature. This determines that emulsified asphalt has many technical and economic advantages over hot asphalt and diluted asphalt. We know that modified asphalt equipment is a road engineering machinery. In order to better promote users’ understanding of it, today the editor will introduce its characteristics to you so that users can better understand that modified asphalt equipment is used for modified asphalt. It consists of a main machine, a modifier feeding system, a finished product tank, a heat transfer oil reheating furnace and a microcomputer control system. The main machine is equipped with a mixing tank, a dilution tank, a colloid mill and an electronic weighing device. The entire production process is controlled by a computer automatic program. In addition, it can be learned that the product has the advantages of reliable quality, stable performance, accurate measurement, and convenient operation. It is an indispensable new equipment in highway construction. The advantages of asphalt equipment are prominently reflected in its two-way modification effect, that is, while greatly increasing the softening point of asphalt, it also significantly enhances the low-temperature ductility, improves the temperature sensitivity, and has a particularly large elasticity and recovery rate. The modified asphalt equipment has a long service life and a safe and reliable production process. The rotor and stator are specially heat treated, and the service life of the equipment is more than 15,000 hours.

Emulsified asphalt equipment improves the fluidity of asphalt: When the emulsified asphalt equipment is subjected to mechanical actions such as high-speed centrifugation, shearing, and impact, the emulsified asphalt equipment makes it into particles with a particle size of 0.1~5μm, and disperses it into a water medium containing a surfactant (emulsifier-stabilizer). Since the emulsifier can be directional adsorbed on the surface of the emulsified asphalt equipment particles, the interfacial tension between water and asphalt is reduced, so that the asphalt particles can form a stable dispersion system in water. The emulsified asphalt equipment is an oil-in-water emulsion.

Fog seal is an asphalt pavement maintenance construction method.
When the asphalt pavement has increased water permeability, loss of fine aggregate, cracks, pitting, etc., a fog seal layer can be used for pavement repair. The bonding material of the fog seal layer is fluid, can repair cracks and gaps, and can heal cracks below 0.3. After construction, the oil content of the road surface is increased, the anti-sticking aggregate is loosened, and it can play a waterproof role.
Before construction, the original road surface should be surveyed and analyzed to determine the construction bonding materials and spray volume.
So what precautions should be taken during construction?

Bitumen emulsion equipment is widely used in new technologies and new processes for preventive maintenance. Bitumen emulsion plant is an emulsion at room temperature formed by dispersing bitumen into the water phase. It is a new material that is made of natural materials. It is different from traditional Compared with hot bitumen, it saves more than 50% of energy, saves 10%-20% of bitumen, and causes less pollution.

From the current point of view, road construction machinery has bottomed out and asphalt meltering equipment has risen rapidly. In recent years, highway construction and maintenance departments have a strong awareness of using asphalt mixing equipment, especially in developed coastal areas such as Beijing, Shanghai, Jiangsu, Zhejiang, etc. In addition, these regions have a fast economic growth rate, relatively developed industry, and strong comprehensive economic strength. Therefore, the consumption of asphalt mixing equipments in these regions has always been at the forefront of the country. With the rapid development of highway construction and the increase in demand for asphalt, barreled asphalt has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported asphalt used in high-grade highways is in barrel form, which requires an asphalt meltering equipment with fast melting speed, clean de-barreling, and can prevent asphalt aging. my country’s highway construction has achieved remarkable results, among which mechanized production has contributed greatly. Different types of asphalt mixers and bitumen meltering equipment are selected for the characteristics of large highway pavement construction and tight construction period. With the rapid development of my country’s economy, the further extension of expressways, and the large-scale development of western construction, the central and western regions have become new investment hotspots. While paying attention to the market in the developed eastern regions, domestic road construction machinery manufacturers have also increased their efforts to develop the central and western markets, creating new highlights for the domestic asphalt mixing plants consumer market. In summary, my country’s asphalt mixing plant sales market has begun to move westward with the westward movement of investment hotspots. As the market center of gravity gradually shifts westward, the market in the western region is gradually heating up. The self-heating integrated structure, hot air barrel melting and bitumen barrel flipping technology in the asphalt barrel removal equipment are our company’s self-heating integrated structure. The thermal oil furnace used in the old equipment is perfectly integrated with the asphalt barrel removal equipment body, which reduces the volume of the entire set of equipment, greatly reduces equipment investment, saves equipment space and transfer transportation costs.

As a black road construction machinery, the synchronous chip sealer is the main equipment for highways, urban roads, airports, and port terminal facilities. Do you know what kind of synchronous chip sealer? What products do you have to choose from?
Asphalt dispensers are classified according to the purpose, operation mode, and drive mode of the asphalt pump. According to the purpose, asphalt dispensers can be divided into two types: road use and road construction use. The asphalt tank capacity of the asphalt dispenser used for road construction generally does not exceed 400L, while the asphalt tank capacity of the asphalt dispenser used for road construction is 3000-20000L.

Synchronous gravel sealing technology refers to the use of special synchronous gravel sealing truck equipment to lay and roll prepared gravel, asphalt and other materials to build a single layer of asphalt gravel wearing layer, which is important for highway pavement. protection of. From the perspective of characteristics, it is simple and easy to implement. It has obvious effects on the prevention of highway diseases, problem solving, later maintenance, and improvement of grade protection. It can also well extend the service life of highways.

Road repair Keep the road to maintain the performance of the road, restore the damaged part in time, ensure the safety, comfort and smooth driving, save transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time. With the performance, the damaged part is restored in time to ensure the safety, comfort and smooth driving, saving transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

Bitumen is a mixture of organic compounds. The road surface paved with bitumen by modified emulsified bitumen equipment is a seamless continuous road surface with good durability and wear resistance. It does not soften at high temperatures and does not crack at low temperatures. It has been promoted and applied worldwide for its superior performance such as strong bearing capacity, no dust, anti-slip, and noise.
Modified bitumen refers to an asphalt mixture that has been improved by adding modifiers such as rubber, resin, high molecular polymer, and finely ground rubber powder, or by lightly oxidizing bitumen. The excellent performance of modified bitumen equipment comes from the modifiers added to it and the world’s advanced colloid mill; the modifiers can not only merge with each other under the action of temperature and kinetic energy, but also react with bitumen, thereby greatly improving the mechanical properties of bitumen. The modified bitumen produced by modified emulsified bitumen equipment can effectively enhance the load capacity of the road surface, reduce the fatigue of the road surface caused by excessive load, and extend the service life of the road surface exponentially. Therefore, it can be widely used in the paving of high-grade highways, airport runways and bridges.

What is an bitumen colloid mill used for? Everyone knows about colloid mill, but what about bitumen colloid mill?
Bitumen colloid mill is a high-tech multifunctional crushing and grinding equipment. The motor drives the rotating teeth and fixed teeth to rotate at high speed, generating a sharp speed gradient, which causes the boring to be strongly sheared, rubbed and turbulent, and finally achieves emulsification and dispersion. and homogenizing effect equipment.

With the development of science and technology, the emergence of emulsified asphalt tanks has brought great convenience to our work, and is widely used in every site. So what issues need to be paid attention to when filling emulsified asphalt tanks? Below, the editor will introduce to you the relevant knowledge structure diagram, hoping to be of some help to you.

Modified material bitumen stripper, if the definition is simple, is an bitumen stripper. If described in detail, modified materials such as rubber powder or other fillers are added to the bitumen stripper, or an bitumen stripper is used to Block chemical substances such as photooxygen catalysis. The first is to change the chemical composition of the bitumen stripper, and the second is to use modified materials to equip the stripper with a certain spatial network structure, thereby improving its performance. Modified bitumen strippers mainly include vulcanized rubber and thermoplastic polyurethane elastomer modified bitumen strippers, plastic and anti-corrosion coating modified bitumen strippers and polymer modified bitumen strippers.

What are the methods for repairing cracks in asphalt pavement? Asphalt pavement is a widely used pavement material in modern road construction, with high strength and durability. However, as time goes by and the frequency of use increases, cracks will inevitably appear in asphalt pavement. So, what are the methods for repairing cracks in asphalt pavement?
What are the methods for repairing cracks in asphalt pavement?
1. Oil filling repair method
This repair method is mainly for smaller cracks or cracks. First, clean the damaged part, then soften the asphalt pavement with a liquefied gas tank, and then pour the thick asphalt into the cracks, and flatten it with a soldering iron, and then carry out normal pavement maintenance. The oil filling repair method is one of the methods for repairing cracks in asphalt pavement, and it is also one of the most commonly used repair methods.
2. Emulsified asphalt seal repair method
This method is mainly for minor cracks or loose cracks. Use a machine to apply a layer of emulsified asphalt on the ground, then sprinkle some stone chips, and finally roll it. This repair method can be constructed on rainy days, with a fast construction speed, and can handle minor crack problems.
3. Cold-patch asphalt mixture repair method
Cold-patch asphalt mixture is one of the asphalt pavement repair materials with good adhesion, wear resistance, and skid resistance. This material is suitable for the repair of various asphalt pavements. It is easy to use and can be quickly opened to traffic after repair, reducing construction time. The color of the cold-patch asphalt mixture is also very different from the original pavement, which can be clearly distinguished and convenient for construction operations.

Emulsion bitumen manchine is widely used in new technologies and new processes for preventive maintenance. Emulsion bitumen manchine is an emulsion at room temperature formed by dispersing asphalt into the water phase. It is a new material that is made of natural materials. It is different from traditional Compared with hot asphalt, it saves more than 50% of energy, saves 10%-20% of asphalt, and causes less pollution.

Is the performance of Sinoroader’s fully automatic emulsified asphalt production equipment stable and unstable? To be honest, whether the performance of a product is stable or not can only be known through practice, right?
Chairman Mao, the great leader of China, once said, “Without practice, there is no right to speak.” Yes, people who have never used it naturally have no right to speak. Now the editor will talk about the fully automatic emulsified asphalt production equipment that I am using!

Working conditions of asphalt debarreling equipment:
(1) Outdoor temperature: 20°C (average temperature of day and night)
(2) Heat exchange oil: 320 ℃
(3) Loading time is not included (because the personnel equipped in each unit are different, so the loading time is also different)
(4) There is no fluctuation in oil temperature (optimal automatic burner)
(5) The working temperature of the oil furnace is 220-260 ℃
(6) The flow rate of the oil circulation pump is not less than 50m3/h traffic
(7) When the outdoor temperature is lower than 20℃, the output decreases. The lower the temperature, the lower the output, and the higher the temperature, the higher the output.
(8) The greater the deformation of the asphalt barrel, the greater the impact on the output

The surface tension of asphalt and water is very different, and they will not be miscible with each other at room temperature or high temperature. However, when the emulsified asphalt equipment is subjected to mechanical actions such as high-speed centrifugation, shearing, and impact, the emulsified asphalt equipment makes it into particles with a particle size of 0.1~5μm, and dispersed in a water medium containing a surfactant (emulsifier-stabilizer). Since the emulsifier can be directional adsorbed on the surface of the emulsified asphalt equipment particles, the interfacial tension between water and asphalt is reduced, so that the asphalt particles can form a stable dispersion system in water. The emulsified asphalt equipment is an oil-in-water emulsion. This dispersion system is tea brown, with asphalt as the dispersed phase and water as the continuous phase, and has good fluidity at room temperature.
In a sense, emulsified asphalt equipment dilutes asphalt with water, thereby improving the fluidity of asphalt.

Asphalt melting equipment is a mechanical equipment specially used to heat and melt asphalt. Our company’s products have been widely recognized and applied in the market.
Our main production process is: transporting the high-temperature oil and gas generated after high-temperature cracking of raw materials (such as petroleum) in the combustion chamber to high-speed rotating heat-conducting oil tankers for heat transfer, melting, cooling and other processes, and finally obtaining the required finished materials or Semi-finished materials. The advantage is that it can make the best use of raw materials and reduce energy consumption; at the same time, it can also customize products of different specifications according to different needs to meet the different requirements of customers. In addition, we provide after-sales service and technical support to protect the interests and safety of our customers.

The slurry seal truck is one of the main maintenance methods of highways. The slurry seal is made of emulsified asphalt as the binding material, well-graded mineral materials, fillers, water and additives, etc., mixed in a certain proportion. The slurry mixture is evenly spread on the old road surface to be treated with a sealing truck, and is firmly combined with the original road surface to form a new thin layer of asphalt mixture. So what preparations need to be done before construction? Let’s find out below.