road construction

With the continuous improvement of science and technology in my country, the application and popularization of bitumen emulsion equipment are also increasing. So how to check whether the configuration meets the standards? Only products that meet the standards can bring us benefits. We must pay attention to this issue. Next, please have a detailed understanding with our factory staff:
1. First of all, we need to check the modified emulsifier. If the gap between the bitumen emulsion colloid mill of the emulsifier will become larger during operation, we need to adjust it before continuous production;
2. Analyze the problem of the modifier. Under normal circumstances, we need to check whether the amount of modifier added is accurate. The time of addition should also adjust the pH value according to the difference in water quality used. This work needs to be operated by technical personnel;
3. Another major reason is caused by the problem of the bitumen emulsion configuration itself. When producing bitumen emulsion, it is necessary to check in advance whether the bitumen material used meets the quality standards.

Microsurfacing is a thin layer of overlay placed on old asphalt pavement and is a type of preventive maintenance process. The purpose of microsurfacing is road maintenance. After micro-surface paving, it can repair cracks in the original road surface, waterproof and beautify the road surface.
The construction method of micro surfacing is: using a micro surfacing paver to evenly spread modified emulsified asphalt, a certain grade of mineral materials, water and other additives on the road surface in a certain proportion.

The advantages of Sinoroader bitumen decanter equipment over similar domestic equipment are reflected in the following points:
1. The equipment produces 8-10t/hour, with an automatic telescopic sealed container structure. It uses an electric hoist to lift the asphalt barrel at the inlet guide tube. Start to control the hydraulic cart forward button, which will promote the barrel push (push and slide into the barrel). It is a 1300mm hydraulic cylinder with a 7.5-ton top thrust. The device has a beautiful appearance, reasonable layout, compactness, stable performance, and is suitable for production under various industrial and mining conditions.
2. Fast barrel removal: According to the principle of layered heating, it adopts four-layer thermal oil heating technology, a single inlet and outlet, and high thermal efficiency of heating; at the same time, it uses the waste heat of combustion gas for two heatings and efficient use of energy; the barrel body uses high-quality rock wool insulation material.
3. Good environmental protection: closed structure, no pollution.
4. No barrel hanging: The upper part of the asphalt barrel is hot, and each is directly affected by the thermal oil heating pipe. The barrel wall directly receives the heat dissipation of the heating coil, and the barrel is clean and fast, which will not cause waste of asphalt barrel hanging.
5. Strong adaptability: Suitable for imported and domestic barrels, and the deformation of asphalt barrels will not affect production.
6. Good dehydration: Use a large-displacement asphalt pump for internal circulation, stirring, water vapor overflows, and is naturally discharged from the exhaust port. After dehydration, asphalt can be directly used to produce asphalt mixture or used as matrix asphalt.
7. Automatic slag removal: This set of equipment has an automatic slag removal function. The filter device sets the asphalt circulation pipeline through the filter, which can automatically remove the barreled asphalt slag.
8. Safe and reliable: The equipment adopts an automatic control system, an automatic ignition burner import, can automatically control the temperature according to the temperature, and is equipped with corresponding monitoring instruments.
9. Convenient relocation: The whole machine is assembled with large components, which is easy to move and quick to assemble.

No matter what product is used, after using it for a period of time, some large and small problems will inevitably arise, which will affect our work, just like the use of asphalt heating equipment will cause problems such as uneven asphalt pavement. We know that for the use of asphalt heating equipment, the construction of asphalt pavement is affected by many factors, including the quality of construction personnel, the quality of roadbed construction, the treatment of the two sections of the bridgehead culvert and the expansion joint of the bridge, the construction of the road subbase and base, the selection of road construction machinery and the quality of road materials. These are the main reasons affecting the flatness of the road surface.
In order to better help customers apply it, professionals introduce the use of asphalt heating equipment. Flatness is an important indicator for measuring the quality of high-grade pavement. Unsmooth pavement will increase driving resistance and cause additional vibrations in the vehicle, which will directly affect the safety and comfort of driving. At the same time, it will aggravate the damage of automobile parts and tires and increase fuel consumption.

The requirements for SBS asphalt emulsification equipment are very high. The micro powder machine must have a sufficiently large driving force and can bear the condensation type. Because the temperature requirements of the emulsion SBS asphalt process are relatively high, the emulsified asphalt should be passed through a heat exchanger before feeding to reduce the emulsified asphalt temperature to below 90°C to prevent the emulsified asphalt from breaking due to excessive temperature.
The application scope of SBS modified emulsified asphalt is very wide. According to the nature of the construction, it can be used in new construction, renovation, and reconstruction projects; according to the nature of the project, it can be used in overhaul, equipment overhaul, and maintenance projects. Among them, the actual application projects include micro-surfacing, cold regeneration, cold mixing and cold paving, adhesive layer, permeable oil, slurry seal, gravel permeable layer, fog permeable layer, road moisture-proofing, SBS membrane, ground seam filling, and all other projects that can use emulsified asphalt.

Bitumen is a mixture of organic compounds. The road surface paved with bitumen by modified emulsified bitumen equipment is a seamless continuous road surface with good durability and wear resistance. It does not soften at high temperatures and does not crack at low temperatures. It has been promoted and applied worldwide for its superior performance such as strong bearing capacity, no dust, anti-slip, and noise.
Modified bitumen refers to an asphalt mixture that has been improved by adding modifiers such as rubber, resin, high molecular polymer, and finely ground rubber powder, or by lightly oxidizing bitumen. The excellent performance of modified bitumen equipment comes from the modifiers added to it and the world’s advanced colloid mill; the modifiers can not only merge with each other under the action of temperature and kinetic energy, but also react with bitumen, thereby greatly improving the mechanical properties of bitumen. The modified bitumen produced by modified emulsified bitumen equipment can effectively enhance the load capacity of the road surface, reduce the fatigue of the road surface caused by excessive load, and extend the service life of the road surface exponentially. Therefore, it can be widely used in the paving of high-grade highways, airport runways and bridges.

Asphalt mixture mixing equipment is a factory-style complete set of equipment that mixes dry and heated aggregates of different particle sizes, fillers and asphalt according to the designed mix ratio at a specified temperature into a uniform mixture. It is widely used in high-grade highways and urban roads. , airports, docks, parking lots and other engineering construction. It is a key equipment for asphalt pavement construction, and its performance directly affects the quality of asphalt pavement.
Generally, there are two types of asphalt concrete mixing equipment: intermittent type and continuous type. The continuous process flow is simple and the equipment is simplified. As for the intermittent forced mixing equipment, due to the secondary screening of aggregates, various components are measured in batches, and forced stirring and mixing can reliably ensure gradation, and the measurement of powder and asphalt can also achieve very high accuracy; so the mixing equipment The asphalt mixture produced is of high quality and can meet various construction requirements.

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

Based on the characteristics of the high-speed hot mixed bitumen melting equipment, the direct heating bitumen melter equipment tank is a researched, environmentally friendly and energy-saving thermal mixed bitumen melting equipment, which can directly coordinate the temperature of the direct heating bitumen melter heating tank and protect the direct heating asphalt melter equipment. Barrel heating tank. The temperature of hot mixed asphalt barrels achieves the appropriate storage temperature.
When the water level in the drum is lower than the temperature of the thermometer, please close the suction valve before the drum pump is shut down to prevent the drum from flowing back in the heater. After the motor has been running for 2 days, the three-way valve opens quickly.

Everyone must be familiar with slurry sealing and micro-surfacing. But do you know their 7 construction steps?
Slurry sealing and micro-surfacing were both early preventative highway protection technologies. Its function is to ensure the smooth use and extended life of the highway. The construction steps are as follows:

Emulsified asphalt equipment is an indispensable equipment in road construction and one of the basic equipment for waterproof coatings. What are the components of emulsified asphalt equipment? Today, we will explain the various parts of emulsified asphalt equipment in detail.
Required parts
Asphalt pump: a device for supplying asphalt to the colloid mill.
Emulsion pump: a device for supplying emulsion to the colloid mill.
Colloid mill: a device for mixing, homogenizing and emulsifying asphalt and emulsion.
Control system: a device for controlling the flow of asphalt and emulsion, and the start and stop of various pumps.
Emulsion blending: a device for mixing water, emulsifiers and other additives.
Water heating part: a device for heating water.

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four heat transfer oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

Emulsified modified asphalt equipment is classified according to the production process and can be divided into three types: intermittent emulsified modified asphalt equipment, semi-continuous emulsified modified asphalt equipment, and continuous emulsified modified asphalt equipment. During the production of emulsified modified asphalt equipment, demulsifier, acid, water, and latex modified materials are blended in a soap mixing tank, and then pumped into the asphalt into the colloid mill. After a can of soap is used up, the soap is redispensed, and then the production of the next can is completed.
The emulsified modified asphalt equipment mentioned here includes hot water pumps and circulation pumps. This type of centrifugal water pump generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. Pay attention to the sewage outlet at the bottom of the emulsified modified asphalt equipment pump. The water in the water tank is released through the filter valve. Some emulsified modified asphalt equipment does not have a filter valve to save equipment costs, so it can only be emptied by loosening the flange bolts at the bottom. There are basically two methods of moisturizing emulsion pumps for emulsified modified asphalt equipment on the market, gear oil pumps or centrifugal water pumps. The gear oil pump can only drain the liquid in the pump through the connecting flange of the pipeline. The centrifugal water pump carries out sewage treatment through its own sewage outlet.
When used in the production of emulsified modified asphalt equipment, depending on the modified material technology, the latex pipeline can be connected in front of the colloid mill or behind the colloid mill, or there may be no latex pipeline and it must be made manually. Add the required amount of latex into the soap jar.

1. Preparation before construction
2. Mix
3. Paving
4. Leveling
5. Shutdown
6. Overlap
7. Crush

Emulsified asphalt equipment improves the fluidity of asphalt: When the emulsified asphalt equipment is subjected to mechanical actions such as high-speed centrifugation, shearing, and impact, the emulsified asphalt equipment makes it into particles with a particle size of 0.1~5μm, and disperses it into a water medium containing a surfactant (emulsifier-stabilizer). Since the emulsifier can be directional adsorbed on the surface of the emulsified asphalt equipment particles, the interfacial tension between water and asphalt is reduced, so that the asphalt particles can form a stable dispersion system in water. The emulsified asphalt equipment is an oil-in-water emulsion.

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four thermal oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

Bitumen decanter equipment can be placed in a complex system as an independent unit, replacing the existing heat source de-barreling method, or in parallel as a core component of a large set of equipment, or it can work independently to meet the requirements of small-scale construction operations.
The Sinoroader bitumen decanter device is mainly composed of a de-barreling box, a lifting mechanism, a hydraulic thruster and an electrical control system. The box is divided into two chambers, the upper chamber is a barreled bitumen melting chamber, and heating coils are evenly distributed around it. The heating pipe and the bitumen barrel mainly exchange heat in a radiation manner to achieve the purpose of bitumen de-barreling. Several guide rails are the tracks for the bitumen barrel to enter. The lower chamber is mainly to continue heating the bitumen removed from the barrel to make the temperature reach the suction pump temperature (100℃), and then the asphalt pump is pumped into the upper chamber. At the same time, an empty barrel is pushed out at the rear end outlet. There is also an oil tank on the platform at the entrance of the asphalt barrel to prevent the dripping bitumen from flowing out.
The inlet and outlet doors of the device adopt a spring automatic closing mechanism. The door can be automatically closed after the asphalt barrel is pushed in or out to reduce heat loss. A temperature gauge is installed at the asphalt outlet to observe the asphalt outlet temperature. The electrical control system can control the opening and closing of the hydraulic pump and the reversing of the electromagnetic reversing valve to realize the advance and retreat of the hydraulic cylinder. If the heating time is extended, a higher temperature can be obtained. The lifting mechanism adopts a cantilever structure. The bitumen barrel is lifted by an electric hoist, and then moved horizontally to place the bitumen barrel on the guide rail. A temperature gauge is installed at the outlet of the asphalt meltering equipment to observe its outlet temperature.

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

1. There are generally three ways to heat emulsified bitumen plant: gas heating, heat transfer oil heating and open flame heating. The first is the gas heating method of emulsified bitumen plant. The gas heating method of emulsified bitumen plant requires the use of the fire pipe to transport the high-temperature smoke generated by high-temperature combustion through the fire pipe.
2. The heat transfer oil heating method of emulsified bitumen plant mainly uses heat transfer oil as a medium for heating. The heat transfer oil heating method has extremely high requirements for fuel. The fuel must be fully burned and the product must be transferred to the heat transfer oil after sufficient heat is transferred to the heat transfer oil pump for heating.
3. The open flame heating method of emulsified bitumen plant is the most direct and convenient heating method. Whether in terms of convenient transportation or coal consumption, the open flame heating method is the fastest choice, simple operation, sufficient fuel, structural design, and labor intensity are relatively reasonable.

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

1. Observation: Pay attention to the dynamics of the road surface after milling (three to four days), and pave the milled and roughened road surface in time when paving conditions are met.
2. On-site mixing: During construction and production, a sealing slurry truck should be used for on-site mixing. Through the metering equipment of the sealing truck and on-site operation by a robot, it is ensured that emulsified asphalt, water, mineral materials, fillers, etc. can be mixed according to a certain proportion. , stir through the mixing box, and the paving thickness is not higher than the roughing depth.

After the emulsified bitumen equipment has been used for a long time, it needs maintenance. There are several points to note when adjusting the emulsified bitumen equipment:
1. During use, regular maintenance should be carried out as appropriate according to the processing materials;
2. For the maintenance and use of the motor, please refer to the motor manual;
3. Most of the random spare parts are national standard and department standard parts, which are purchased all over the country;
4. The colloid mill is a high-precision machine with a line speed of up to 20m/second and a very small grinding disc gap. After inspection and reinstallation, the coaxiality error between the housing and the main shaft must be corrected with a dial indicator ≤0.05mm;
5. When repairing the machine, it is not allowed to be directly knocked with an iron bell during the disassembly, reinstallation and adjustment process. Use a wooden hammer or a wooden block to knock gently to avoid damaging the parts;
6. The machine seals: divided into static and dynamic seals. The static seal uses an O-type rubber ring and the dynamic seal uses a hard mechanical combined seal. If the hard sealing surface is scratched, it should be repaired by grinding on flat glass or flat casting immediately. The grinding material should be ≥200# silicon carbide grinding paste. If the seal is damaged or cracked seriously, please replace it immediately.

As technology becomes more and more advanced, we use more and more equipment in our lives, and the functions are also very complete. Synchronous crushed stone seal is also a product used in many places. After continuous improvement and development, it has many functions. Next, we will introduce to you the problem of preventive maintenance of synchronous crushed stone seal? If you want to know, you can read it together.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

● The spreading amount is accurate, and three overlapping asphalt sprayings can be achieved with good uniformity;
● Intelligent control of spreading amount, real-time monitoring of spreading amount and vehicle speed, closed-loop control;
● Full computer touch screen operation, equipped with video monitoring system, the entire work process can be observed at any time;
● Reliable performance, durability and easy operation;

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

Emulsion bitumen manchine is widely used in new technologies and new processes for preventive maintenance. Emulsion bitumen manchine is an emulsion at room temperature formed by dispersing asphalt into the water phase. It is a new material that is made of natural materials. It is different from traditional Compared with hot asphalt, it saves more than 50% of energy, saves 10%-20% of asphalt, and causes less pollution.

The asphalt spreading truck is an intelligent high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, heavy traffic asphalt and modified asphalt. It is used in highway construction and highway maintenance projects, and can be used for the construction of upper and lower seals, permeable layers, waterproof layers, bonding layers, asphalt surface treatment, asphalt penetration pavements, fog seals and other projects of different grades of highway pavements. , can also be used for the transportation of liquid asphalt or other heavy oil. So what are the advantages of Qiangguomeng’s asphalt spreader trucks?

We need to prepare a lot of work when using modified asphalt equipment. What kind of work do we need to prepare? Next, let me briefly introduce the relevant knowledge points.
1. Heat transfer oil heats and insulates the modified asphalt equipment and nozzle. After spraying, the asphalt pump and nozzle do not need to be cleaned with diesel. Use high-pressure air to press the asphalt in the pipeline and spray pipe back to the tank, and then blow the nozzle; use heat transfer oil to keep warm, so that the pipeline and nozzle are smooth and unobstructed. 2. Various asphalts can be spread: high-viscosity asphalt, hot asphalt, emulsified asphalt, etc.; the spreading width can be freely adjusted, each nozzle can be controlled separately, and the maximum spraying width is up to 6m. Flexible handheld spray guns can be used to spray asphalt on corners. 3. Excellent thermal insulation performance, average cooling ≤1-2℃/h. 4. Convenient loading and unloading function. In addition to filling asphalt from the asphalt tank port, hot asphalt can be sucked out by itself, and external asphalt can also be pumped and transferred. 5. The modified asphalt equipment is evenly spread, and the nozzle design can be used for triple overlapping spraying.
The above are the relevant knowledge points of modified asphalt equipment. I hope the above content can be helpful to everyone. Thank you for your viewing and support. More information will be sorted out for you later. Please pay attention to our website updates.