How to repair emulsified bitumen equipment?

Preparation items for micro-surfacing slurry sealing: materials, construction machinery (micro-surfacing paver) and other auxiliary equipment.
The micro-surface slurry seal requires emulsified asphalt and stone that meet the standards. The metering system of the micro-surfacing paver needs to be calibrated before construction. The production of emulsified asphalt requires asphalt heating tanks, emulsified asphalt production equipment (capable of producing asphalt content greater than or equal to 60%), and emulsified asphalt finished product tanks. In terms of stone, mineral screening machines, loaders, forklifts, etc. are needed to screen out oversized stones.
The tests required include emulsification test, screening test, mixing test and the equipment and technical personnel required to do these tests.

Synchronous gravel sealer fog sealer is a method of road maintenance. Some roads have network cracks, cracks and holes after a few years of use. The effective method is fog seal technology. The cost is very low. After the fog seal, due to the large fluidity of the material, it can penetrate into the aggregate and flow into the cracks to “transfuse” the road surface, restore the asphalt adhesion of the road surface, fill small cracks and gaps, prevent water from penetrating the road surface, and keep the road surface performance for 2 to 3 years, delaying the high maintenance cost and improving the economic benefits.

We have conducted in-depth research on asphalt distributors and have accumulated a lot of production technology experience. We have conducted professional and in-depth research on some problems existing in the market to provide convenience for everyone in future production applications.
Every time when spraying asphalt, the asphalt distributor does not spray asphalt. Troubleshooting. The asphalt distributor does not spray asphalt. It is a common fault. The following teaches you how to solve the problem of not spraying asphalt.
1. No asphalt spraying
Analysis of the reasons may be the following reasons:
1. Is the asphalt pump working?
2. Are the valves adjusted correctly?
3. Is the pump or pipeline blocked?
2. Troubleshooting method
1. Check whether the hydraulic system is working properly?
2. After adjusting the valve position, the asphalt distributor must be cleaned to avoid pipeline blockage when used next time. Because the asphalt distributor has different high and low configurations, it can spread various high-viscosity and high-temperature modified asphalts and rubber asphalt in high configuration. If you mistakenly use a low-configuration asphalt truck to spread this type of asphalt, you must spray the asphalt inside the entire vehicle clean after the first use. After spraying, in order to leave no residual asphalt, you can use waste diesel to clean it. Our company’s vehicles are equipped with air cleaning and gravity cleaning devices. Diesel cleaning is a reliable cleaning method.

Regarding the basic knowledge of modified bitumen plant, I believe that many consumers have already had a basic understanding of it. Because of the continuous development of various fields today, various facilities including modified bitumen plants have been well developed and applied, and modified bitumen plant has gradually been recognized by customers.
The direct quick heating portable equipment in the modified bitumen equipment not only has a faster heating speed, saves fuel, and is pollution-free, but also convenient and easy to operate. The automatic heating system completely eliminates the trouble of baking or cleaning bitumen and pipelines.

Maintenance points of asphalt spreading trucks in different working hours
per month (or every 200 hours worked)；
​Per year (or every 500 hours worked)；
Every two years (or every 1,000 hours worked)；

After the emulsified asphalt equipment has been used for a long time, it needs maintenance. There are several points to note when adjusting the emulsified asphalt equipment:
1. During use, regular maintenance should be carried out as appropriate according to the processing materials;
2. For the maintenance and use of the motor, please refer to the motor instruction manual;
3. Most of the random spare parts are national standard and department standard parts, which are purchased all over the country;
4. The colloid mill is a high-precision machine with a line speed of up to 20m/second and a very small grinding disc gap. After overhaul, the coaxiality error between the housing and the main shaft must be corrected with a dial indicator to ≤0.05mm;
5. When repairing the machine, it is not allowed to be directly knocked with an iron bell during the disassembly, reassembly and adjustment process. Use a wooden hammer or a wooden block to knock gently to avoid damaging the parts;
6. The seals of this machine are divided into static and dynamic seals. The static seal uses an O-type rubber ring and the dynamic seal uses a hard mechanical combined seal. If the hard sealing surface is scratched, it should be repaired by grinding on flat glass or flat castings immediately. The grinding material should be ≥200# silicon carbide grinding paste. If the seal is damaged or cracked seriously, please replace it immediately.

Fog seal is an asphalt pavement maintenance construction method.
When the asphalt pavement has increased water permeability, loss of fine aggregate, cracks, pitting, etc., a fog seal layer can be used for pavement repair. The bonding material of the fog seal layer is fluid, can repair cracks and gaps, and can heal cracks below 0.3. After construction, the oil content of the road surface is increased, the anti-sticking aggregate is loosened, and it can play a waterproof role.
Before construction, the original road surface should be surveyed and analyzed to determine the construction bonding materials and spray volume.
So what precautions should be taken during construction?

The container-type emulsified bitumen equipment hot-melts the base cold-mix colored bitumen and disperses it through the equipment into small cold-mix colored bitumen particles in an aqueous solution containing emulsifier to form a liquid cold-mix colored bitumen material.

Everyone has a side of themselves that they don’t want others to know. As a preventive road maintenance technology, slurry sealing has some shortcomings. do you think so?
Slurry seal is a kind of road protection that uses special equipment to mix emulsified asphalt, water, additives, aggregates, fillers and other ingredients in a certain proportion, and then mixes the slurry mixture onto the original road surface to form a thin layer. Maintenance technology. These are all well known. The editor will not go into details on this.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

We should select products that meet the specifications, and we should not select raw materials that do not meet the specifications. The other thing is the operation technology of asphalt heating equipment. Skilled operation technology is the most important, and training is required before taking up the post.
In recent years, with the continuous development of various industries, the production of various equipment including modified asphalt equipment has been further developed and applied. Professionals introduced that in the process of using modified asphalt equipment for production, the terminal control system implements full automatic control of medium weight, working temperature, working flow, valve opening and closing, etc., thereby ensuring the quality of modified asphalt and greatly improving production efficiency. Now Shandong Duxiu Factory will explain the operating advantages of modified asphalt equipment to customers:
The base asphalt is heated to 150-170℃ in the rapid heating tank and then enters the blending tank to mix with the modifier fed in through the feeding device. The asphalt pump at the bottom of the blending tank then sends it to the colloid mill for high-speed grinding and shearing, so that the modifier and base asphalt are fully dissolved in extremely small particles, thereby improving the various properties of the asphalt. The finished modified asphalt after high-speed shearing and grinding enters the finished product development tank at the rear for direct use.

The modified asphalt equipment produced by Sinoroader can produce SBS, rubber powder, SBR, and PE modified asphalt manually and automatically. Some of its configurations and uses are as follows:
1. Filter: The specially made asphalt filter can effectively filter impurities and foreign matter in the high-temperature matrix asphalt to prevent damage to subsequent equipment.
2. Matrix asphalt heater: The spiral plate or shell and tube heat exchanger is used to quickly heat the matrix asphalt through heat transfer oil to meet the needs of the production process. Heating in a sealed tank avoids the aging of asphalt due to long-term high-temperature heating and exposure to the air. The sulfide produced during the production process is quite limited, reducing environmental pollution.
3. Modifier air delivery or spiral addition system: The modifier manually poured into the pouring hopper is delivered to the asphalt batching tank by wind or spiral. It can be equipped with a metering system.
4. Stabilizer automatic or manual addition system: It can be equipped with a metering system.

The modified asphalt equipment estimates the quality and uniformity of various raw materials from the material pile and conveyor at any time. The modified asphalt equipment checks the soil and oversized gravel, and checks whether there is any leakage in the cold hopper. Estimate whether the mixed material is mixed evenly, whether there is white material, whether the oil-stone ratio is reasonable, and check the concrete segregation of the asphalt mixture and the mixed material.
The modified asphalt equipment checks the control parameters of various basic parameters of the mixing device in the control room, the display values ??of the control screen, and the modified asphalt equipment checks whether the data statistics and display values ??of the computer and printout are consistent. Test the raw material heating temperature and the mixed material entry temperature of the modified asphalt equipment.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Technical features of fiber sealing equipment:
1. Zero starting strong injection technology
With more than ten years of manufacturing history of asphalt spreading trucks and asphalt gravel synchronous sealing trucks, the zero-start strong spraying technology has been accumulated for many years. The combination of time-reliable hydraulic transmission components and Meitong’s control system can make the equipment instantly start from zero. Spraying starts in line, stable and reliable.
2. Duplex sealing structure
The sealing process of this equipment is a three-layer simultaneous and continuous construction process of one layer of asphalt + one layer of fiber + one layer of asphalt, forming a layer of interactive dense network winding structure, which fully meets the user’s construction requirements.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four heat transfer oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.

● The spreading amount is accurate, and three overlapping asphalt sprayings can be achieved with good uniformity;
● Intelligent control of spreading amount, real-time monitoring of spreading amount and vehicle speed, closed-loop control;
● Full computer touch screen operation, equipped with video monitoring system, the entire work process can be observed at any time;
● Reliable performance, durability and easy operation;

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.

Based on the characteristics of the high-speed hot mixed bitumen melting equipment, the direct heating bitumen melter equipment tank is a researched, environmentally friendly and energy-saving thermal mixed bitumen melting equipment, which can directly coordinate the temperature of the direct heating bitumen melter heating tank and protect the direct heating asphalt melter equipment. Barrel heating tank. The temperature of hot mixed asphalt barrels achieves the appropriate storage temperature.
When the water level in the drum is lower than the temperature of the thermometer, please close the suction valve before the drum pump is shut down to prevent the drum from flowing back in the heater. After the motor has been running for 2 days, the three-way valve opens quickly.

Emulsified asphalt equipment hot-melts basic colored asphalt and mechanically distributes tiny colored asphalt particles in an aqueous solution containing emulsifier to form a liquid colored asphalt material. The cement emulsified asphalt equipment mortar used in slab ballastless track construction uses cationic emulsified asphalt equipment. The purpose is to adjust the elasticity, toughness and durability of the cement emulsified asphalt equipment mortar. Polymers are often used to modify the asphalt.

How to reduce the energy consumption of emulsified asphalt production equipment is a concern of many users, and is also an issue that many manufacturers attach great importance to. Therefore, today Sinoroader, as a manufacturer of emulsified asphalt production equipment, would like to take this opportunity to share with you how to reduce the production of emulsified asphalt. Equipment energy consumption method.
Since emulsified asphalt appears as a finished product in emulsified asphalt production equipment, and the outlet temperature of ordinary emulsified asphalt is about 85°C, the outlet temperature of emulsified modified asphalt is above 95°C, so there is a lot of latent heat in emulsified asphalt, but emulsified asphalt The production equipment does not make good use of them, but directly enters the finished product tank, allowing the heat to be lost at will, resulting in a waste of energy.

There are many ways to heat bitumen, including using fire source heating, electric heating, steam heating, hot water heating and indirect heating. Fire source heating generates heat by burning fuel to heat the bitumen to a molten state. Electric heating converts electrical energy into thermal energy through electric heating elements to heat the bitumen to a molten state. Steam heating transfers heat to bitumen through steam, heating the bitumen to a molten state. Hot water heating transfers heat to the bitumen through hot water, heating the bitumen to a molten state. Indirect heating transfers heat to the heating medium, which then transfers the heat to the bitumen to heat the bitumen to a molten state.

As we all know, emulsified bitumen is a single-component black viscous liquid that can combine the roadbed and the pavement to improve the performance and service life of the road. So what problems should be paid attention to when using emulsified bitumen? Let’s follow the editor of Sinoroader Group, an emulsified bitumen manufacturer, to learn about it.

As a manufacturer with many years of experience in emulsified bitumen construction, Sinoroader Group believes that everyone needs to pay attention to the following 2 points when using it:

The bitumen decanter equipment is mainly composed of barrel removal shell (BOX), hoisting mechanism, hydraulic booster and electrical control system. The shell is divided into two chambers, the left and right chambers. The upper chamber is a chamber for melting a large barrel of bitumen (definition: the transformation process of a substance from solid to liquid). There are heating coils evenly distributed around it.

Emulsified asphalt is an emulsion that disperses asphalt into the water phase to form a liquid at room temperature. This determines that emulsified asphalt has many technical and economic advantages over hot asphalt and diluted asphalt. We know that modified asphalt equipment is a road engineering machinery. In order to better promote users’ understanding of it, today the editor will introduce its characteristics to you so that users can better understand that modified asphalt equipment is used for modified asphalt. It consists of a main machine, a modifier feeding system, a finished product tank, a heat transfer oil reheating furnace and a microcomputer control system. The main machine is equipped with a mixing tank, a dilution tank, a colloid mill and an electronic weighing device. The entire production process is controlled by a computer automatic program. In addition, it can be learned that the product has the advantages of reliable quality, stable performance, accurate measurement, and convenient operation. It is an indispensable new equipment in highway construction. The advantages of asphalt equipment are prominently reflected in its two-way modification effect, that is, while greatly increasing the softening point of asphalt, it also significantly enhances the low-temperature ductility, improves the temperature sensitivity, and has a particularly large elasticity and recovery rate. The modified asphalt equipment has a long service life and a safe and reliable production process. The rotor and stator are specially heat treated, and the service life of the equipment is more than 15,000 hours.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement