Performance advantages of high-quality fully automatic asphalt spreaders

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

After the emulsified asphalt equipment has been used for a long time, it needs maintenance. There are several points to note when adjusting the emulsified asphalt equipment:
1. During use, regular maintenance should be carried out as appropriate according to the processing materials;
2. For the maintenance and use of the motor, please refer to the motor instruction manual;
3. Most of the random spare parts are national standard and department standard parts, which are purchased all over the country;
4. The colloid mill is a high-precision machine with a line speed of up to 20m/second and a very small grinding disc gap. After overhaul, the coaxiality error between the housing and the main shaft must be corrected with a dial indicator to ≤0.05mm;
5. When repairing the machine, it is not allowed to be directly knocked with an iron bell during the disassembly, reassembly and adjustment process. Use a wooden hammer or a wooden block to knock gently to avoid damaging the parts;
6. The seals of this machine are divided into static and dynamic seals. The static seal uses an O-type rubber ring and the dynamic seal uses a hard mechanical combined seal. If the hard sealing surface is scratched, it should be repaired by grinding on flat glass or flat castings immediately. The grinding material should be ≥200# silicon carbide grinding paste. If the seal is damaged or cracked seriously, please replace it immediately.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

1. Observation: Pay attention to the dynamics of the road surface after milling (three to four days), and pave the milled and roughened road surface in time when paving conditions are met.
2. On-site mixing: During construction and production, a sealing slurry truck should be used for on-site mixing. Through the metering equipment of the sealing truck and on-site operation by a robot, it is ensured that emulsified asphalt, water, mineral materials, fillers, etc. can be mixed according to a certain proportion. , stir through the mixing box, and the paving thickness is not higher than the roughing depth.

For each equipment used, certain safety knowledge must be followed. For the use of emulsified asphalt equipment, detailed instructions are given:
1. Placement: The emulsified asphalt equipment should be placed on a flat place, the front axle should be fixed to the sleepers, and the tires should be dangling. The machine should not be fiddled with at will to affect normal operation.
2. Regularly check whether the mixer blades are deformed and the screws are loose.
3. Check whether the running direction of the mixing drum is consistent with the direction of the arrow. Please replace the positive and negative poles of the terminal.
4. Before turning on the power, check the no-load test run, check for air leakage, and check the idling speed of the mixing barrel. The normal speed is about 3 times faster than the empty car. If not, stop the inspection.
5. If the asphalt material is stopped for one hour after mixing, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water in the barrel to prevent the formula from changing, so that the page and other links will rust. Sinoroader will provide you with more safe emulsified asphalt knowledge, please continue to browse.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Road repair Keep the road to maintain the performance of the road, restore the damaged part in time, ensure the safety, comfort and smooth driving, save transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time. With the performance, the damaged part is restored in time to ensure the safety, comfort and smooth driving, saving transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time.

Asphalt spreading trucks are used to spread the permeable oil layer, waterproof layer and bonding layer of the bottom layer of asphalt pavement on high-grade highways. It can also be used in the construction of county and township-level highway asphalt roads that implement layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.

The hydraulic bitumen decanter equipment produced by our company uses thermal oil as the heat carrier and has its own burner for heating. The thermal oil heats, melts, debarks and dehydrates the asphalt through the heating coil. This device can ensure that the asphalt does not age, and has the advantages of high thermal efficiency, fast barrel loading/unloading speed, improved labor intensity, and reduced environmental pollution.

Bitumen is a mixture of organic compounds. The road surface paved with bitumen by modified emulsified bitumen equipment is a seamless continuous road surface with good durability and wear resistance. It does not soften at high temperatures and does not crack at low temperatures. It has been promoted and applied worldwide for its superior performance such as strong bearing capacity, no dust, anti-slip, and noise.
Modified bitumen refers to an asphalt mixture that has been improved by adding modifiers such as rubber, resin, high molecular polymer, and finely ground rubber powder, or by lightly oxidizing bitumen. The excellent performance of modified bitumen equipment comes from the modifiers added to it and the world’s advanced colloid mill; the modifiers can not only merge with each other under the action of temperature and kinetic energy, but also react with bitumen, thereby greatly improving the mechanical properties of bitumen. The modified bitumen produced by modified emulsified bitumen equipment can effectively enhance the load capacity of the road surface, reduce the fatigue of the road surface caused by excessive load, and extend the service life of the road surface exponentially. Therefore, it can be widely used in the paving of high-grade highways, airport runways and bridges.

Conventional pit repair techniques are mainly hot material repair and cold filling repair, and warm mixing technology is used to ensure compaction, while there are also some special repair methods such as slurry seal/micro-surface material repair

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four thermal oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

Asphalt melting equipment is an important road construction tool used to heat asphalt to the appropriate temperature for construction. It can provide reliable solutions and make road construction more convenient. The working principle of this equipment is to heat the asphalt to the appropriate temperature through a heater, and then transport the hot asphalt to the construction site through a conveying system.

When performing bitumen melting, specialized equipment is required. These equipment usually include bitumen melting furnaces, asphalt mixers, asphalt conveying equipment, etc. Among them, the bitumen melting furnace is one of the most advanced equipments, which can heat solid bitumen to liquid state. In addition, asphalt mixers can mix liquid asphalt with stone to make asphalt concrete. , Asphalt conveying equipment can transport asphalt concrete to the construction site. The selection and use of these equipment are of great significance to ensure the quality of bitumen melting and construction efficiency.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

There are many types of emulsified bitumen, and PC-2 is one of them, which is a spray-type emulsified bitumen. It is used for spraying oil through the base layer of granular materials and health care spraying on semi-rigid base layers. There is also the PA-2 type, which has the same purpose as the PC-2 type. The difference is that the PC-2 type is a cation, while the PA-2 type is an anion.

The modified asphalt equipment produced by Sinoroader can produce SBS, rubber powder, SBR, and PE modified asphalt manually and automatically. Some of its configurations and uses are as follows:
1. Filter: The specially made asphalt filter can effectively filter impurities and foreign matter in the high-temperature matrix asphalt to prevent damage to subsequent equipment.
2. Matrix asphalt heater: The spiral plate or shell and tube heat exchanger is used to quickly heat the matrix asphalt through heat transfer oil to meet the needs of the production process. Heating in a sealed tank avoids the aging of asphalt due to long-term high-temperature heating and exposure to the air. The sulfide produced during the production process is quite limited, reducing environmental pollution.
3. Modifier air delivery or spiral addition system: The modifier manually poured into the pouring hopper is delivered to the asphalt batching tank by wind or spiral. It can be equipped with a metering system.
4. Stabilizer automatic or manual addition system: It can be equipped with a metering system.

1. When operating an asphalt spreading truck, first check whether the machinery, spreading devices, protective and fire prevention equipment are complete and effective.
2. It is strictly prohibited to use non-specified fuel as the fuel for the heating system. The fuel is not allowed to overflow outside the tank. Generally, the oil level should be 20-30cm lower than the upper end of the overflow pipe.

There are many ways to heat bitumen, including using fire source heating, electric heating, steam heating, hot water heating and indirect heating. Fire source heating generates heat by burning fuel to heat the bitumen to a molten state. Electric heating converts electrical energy into thermal energy through electric heating elements to heat the bitumen to a molten state. Steam heating transfers heat to bitumen through steam, heating the bitumen to a molten state. Hot water heating transfers heat to the bitumen through hot water, heating the bitumen to a molten state. Indirect heating transfers heat to the heating medium, which then transfers the heat to the bitumen to heat the bitumen to a molten state.

The bitumen (composition: asphaltene and resin) drum melting machine adopts a self-heating integrated structure, which integrates the thermal oil boiler used in the old asphalt drum melting machine and the barrel removal equipment itself, reducing the volume of the entire equipment and significantly It reduces equipment investment (actual significance: it is the accumulation of future profits), saves the space occupied by the equipment and the logistics cost of switching sites. The combustion chamber is placed inside the equipment itself, which greatly reduces thermal damage and improves heat utilization.

Emulsified asphalt equipment improves the fluidity of asphalt: When the emulsified asphalt equipment is subjected to mechanical actions such as high-speed centrifugation, shearing, and impact, the emulsified asphalt equipment makes it into particles with a particle size of 0.1~5μm, and disperses it into a water medium containing a surfactant (emulsifier-stabilizer). Since the emulsifier can be directional adsorbed on the surface of the emulsified asphalt equipment particles, the interfacial tension between water and asphalt is reduced, so that the asphalt particles can form a stable dispersion system in water. The emulsified asphalt equipment is an oil-in-water emulsion.

Everyone must be familiar with slurry sealing and micro-surfacing. But do you know their 7 construction steps?
Slurry sealing and micro-surfacing were both early preventative highway protection technologies. Its function is to ensure the smooth use and extended life of the highway. The construction steps are as follows:

Asphalt sealant is a material specially used for road crack repair. The following is a detailed introduction to asphalt sealant:
1. Definition and composition
Asphalt sealant is a road repair material made of asphalt or modified asphalt as the base material, with a certain amount of additives and fillers added, and processed by special technology. It usually has a black or dark brown appearance and is in a solid or semi-solid form.
2. Main characteristics
High adhesion: Asphalt sealant can firmly bond to the crack wall of the road surface to form a tight sealing layer to prevent moisture and other harmful substances from invading the road surface structure.
High elasticity: It has a certain elastic recovery ability and can adapt to the expansion and contraction changes of the road surface to prevent further expansion of cracks.
Weather resistance: After special process treatment, it has good weather resistance and can maintain its stable performance for a long time.
Convenient construction: The construction operation is simple and fast, without complex construction machinery, which reduces the construction cost.
3. Scope of application
Asphalt sealant is widely used in crack repair of various asphalt pavements, including highways, urban roads, airport runways, etc. At the same time, it can also be used for the maintenance and repair of asphalt surfaces such as bridges, tunnels, and parking lots.

Emulsified asphalt equipment hot-melts basic colored asphalt and mechanically distributes tiny colored asphalt particles in an aqueous solution containing emulsifier to form a liquid colored asphalt material. The cement emulsified asphalt equipment mortar used in slab ballastless track construction uses cationic emulsified asphalt equipment. The purpose is to adjust the elasticity, toughness and durability of the cement emulsified asphalt equipment mortar. Polymers are often used to modify the asphalt.

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.

The asphalt spreading truck is an intelligent high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, heavy traffic asphalt and modified asphalt. It is used in highway construction and highway maintenance projects, and can be used for the construction of upper and lower seals, permeable layers, waterproof layers, bonding layers, asphalt surface treatment, asphalt penetration pavements, fog seals and other projects of different grades of highway pavements. , can also be used for the transportation of liquid asphalt or other heavy oil. So what are the advantages of Qiangguomeng’s asphalt spreader trucks?

The modified asphalt equipment estimates the quality and uniformity of various raw materials from the material pile and conveyor at any time. The modified asphalt equipment checks the soil and oversized gravel, and checks whether there is any leakage in the cold hopper. Estimate whether the mixed material is mixed evenly, whether there is white material, whether the oil-stone ratio is reasonable, and check the concrete segregation of the asphalt mixture and the mixed material.
The modified asphalt equipment checks the control parameters of various basic parameters of the mixing device in the control room, the display values ??of the control screen, and the modified asphalt equipment checks whether the data statistics and display values ??of the computer and printout are consistent. Test the raw material heating temperature and the mixed material entry temperature of the modified asphalt equipment.