The key to improving the construction efficiency of asphalt melting equipment in daily operations

There are many types of bitumen emulsifiers, and there are many classification methods. For specific classifications, please refer to previous articles. The raw materials required for the production of emulsion bitumen are: bitumen, water and bitumen emulsifier. High-standard emulsion bitumen requires adding additives and adjusting acid. According to whether acid adjustment is needed in the emulsion bitumen production process, it can be divided into two categories: emulsion bitumen that requires acid adjustment and emulsion bitumen that does not require acid adjustment.

This set of mechanical equipment includes wastewater treatment, water storage tank, automatic water measurement and verification temperature control system, asphalt storage tank, asphalt external temperature system, hot water pump soap condiment system, soap storage tank, soap mixing pump, soap external It is composed of temperature system and measurement verification system, filtration system, hot asphalt mixing pump and measurement verification system, three-stage pipeline-type black antistatic medical tweezers, emulsified asphalt cooling system and retrieval machinery, and automatic control system for commercial tanks and electrical equipment.

Working conditions of asphalt debarreling equipment:
(1) Outdoor temperature: 20°C (average temperature of day and night)
(2) Heat exchange oil: 320 ℃
(3) Loading time is not included (because the personnel equipped in each unit are different, so the loading time is also different)
(4) There is no fluctuation in oil temperature (optimal automatic burner)
(5) The working temperature of the oil furnace is 220-260 ℃
(6) The flow rate of the oil circulation pump is not less than 50m3/h traffic
(7) When the outdoor temperature is lower than 20℃, the output decreases. The lower the temperature, the lower the output, and the higher the temperature, the higher the output.
(8) The greater the deformation of the asphalt barrel, the greater the impact on the output

Friends who are ready to get started have a surprise today. The editor will give you a brief introduction on how to produce emulsified asphalt.

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

According to the configuration, layout and controllability of bitumen melting equipment, bitumen melting plant can be divided into three types: mobile, transportable and portable. What should be paid attention to in the production of bitumen melter equipment of different sizes? Let’s learn about it below!
Bitumen melting plant is to fix the demulsifier mixing equipment, black anti-static tweezers, asphalt pump, automatic control system, etc. on a special support chassis. Because the bitumen melter equipment can directly change the production site, it is suitable for the production of emulsion bitumen in construction sites with decentralized projects, small usage and frequent movement.
The main components of the bitumen melting equipments are installed in one or two 60 standard containers. The bitumen melting plant is loaded and transported separately to complete the relocation of the construction site. With the help of asphalt melting equipments hoisting equipment, it is quickly installed and put into operation. Such bitumen melter plant has large, medium and small different configurations, which can meet different project requirements.

What is an bitumen colloid mill used for? Everyone knows about colloid mill, but what about bitumen colloid mill?
Bitumen colloid mill is a high-tech multifunctional crushing and grinding equipment. The motor drives the rotating teeth and fixed teeth to rotate at high speed, generating a sharp speed gradient, which causes the boring to be strongly sheared, rubbed and turbulent, and finally achieves emulsification and dispersion. and homogenizing effect equipment.

Abstract: Asphalt melting equipment is one of the indispensable equipment in modern road construction. Its main function is to heat a large amount of cold hard asphalt to a suitable working temperature at the construction site. Advanced asphalt melting equipment can greatly improve construction efficiency, reduce human resources and time costs, and ensure pavement quality at the same time.

For each equipment used, certain safety knowledge must be followed. For the use of emulsified asphalt equipment, detailed instructions are given:
1. Placement: The emulsified asphalt equipment should be placed on a flat place, the front axle should be fixed to the sleepers, and the tires should be dangling. The machine should not be fiddled with at will to affect normal operation.
2. Regularly check whether the mixer blades are deformed and the screws are loose.
3. Check whether the running direction of the mixing drum is consistent with the direction of the arrow. Please replace the positive and negative poles of the terminal.
4. Before turning on the power, check the no-load test run, check for air leakage, and check the idling speed of the mixing barrel. The normal speed is about 3 times faster than the empty car. If not, stop the inspection.
5. If the asphalt material is stopped for one hour after mixing, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water in the barrel to prevent the formula from changing, so that the page and other links will rust. Sinoroader will provide you with more safe emulsified asphalt knowledge, please continue to browse.

Urban road maintenance is an important part of ensuring road safety and smooth traffic, among which slurry seal and micro-surfacing are two common maintenance methods.
Slurry seal:
Composition: emulsified asphalt or modified emulsified asphalt
Function: waterproof, anti-skid, improve road surface appearance
Scope of application: cover surface of secondary trunk roads, lower seal layer of newly built roads
Micro-surfacing:
Composition: modified asphalt
Function: waterproof, anti-skid, wear-resistant, improve road surface appearance, repair ruts
Scope of application: expressways, trunk roads
Construction process:
Cleaning the road surface
Laying out the lines
Wetting the original road surface
Paving
Repairing
Maintenance
Opening traffic
Test section length ≥ 200m
When the original road surface is an asphalt road surface, it needs to be wetted with water in dry or hot weather; non-asphalt road surfaces should be sprayed with tack coat oil; the lower seal layer of semi-rigid base asphalt road surfaces needs to be sprayed with penetration oil.
For sections that need to be opened to traffic as soon as possible, a thin layer of sand can be spread.
Quality acceptance:
Before construction, check the test report of raw materials, slurry mixture design report, and paver calibration report.
The entire construction line is evaluated as a 1km section.
The main control items include skid resistance, water permeability, and thickness.
Through these steps, the service life of the road can be effectively extended and driving safety can be ensured.

Detailed summary of slurry seal specifications

Asphalt spreader vehicle is an intelligent and automated high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, high-viscosity modified asphalt, etc.
Asphalt spreader is used for spreading the penetration oil, waterproof layer, and bonding layer of the bottom layer of the asphalt pavement of high-grade highways. The spreader consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, an ignition system, a control system, a pneumatic system, and an operating platform.
Asphalt spreader is cumbersome to operate. On the basis of absorbing various technologies of similar products at home and abroad, it increases the quality technology content of construction and the humanized design of outstanding improvement of construction conditions and construction environment. Its reasonable and reliable design ensures the uniformity of asphalt spreading, the computer control is stable and reliable, and the technical performance of the whole vehicle has reached an advanced level.

Slurry sealers are important equipment for road maintenance and repair. They are mainly used to pour durable asphalt mixtures on old roads to form a new protective layer. This equipment can be constructed according to the surface texture of the road surface, so that the cracks in the surface layer are isolated from water and air, effectively preventing the road surface from aging further.
The working principle of the slurry sealer is to mix materials such as aggregate, emulsified asphalt and additives into slurry, and then evenly lay it on the road surface. The slurry formed after the mixture of these materials has good waterproof and skid resistance, which can significantly improve the service life of the road surface and driving safety.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

The heating principle of asphalt decanter equipment is to heat, melt and decanter the asphalt through the heating plate. It is mainly composed of de-barreling box, lifting system, propeller and electrical control system.
The box of asphalt decanter plant is divided into upper and lower chambers. The upper chamber is the asphalt melting chamber, which is densely covered with heat transfer oil heating coils or hot air heating pipes. The asphalt is melted and removed from the barrel by heat. The hoisting hook is installed on the gantry, and a barrel grabber is hung. The asphalt barrel is lifted by the electric winch, and then the asphalt barrel is placed on the guide rail by horizontal movement. Then the propeller pushes the barrel into the upper chamber through two guide rails, and an empty barrel is pushed out at the rear end outlet.
An anti-drip oil tank is provided at the entrance of the asphalt barrel. The asphalt enters the lower chamber of the box and is continuously heated to a temperature of about 100 to be transported, and then pumped into the asphalt tank by the asphalt pump. The lower chamber can also be used as an asphalt heating tank.
The asphalt decanter plant has the characteristics of not being restricted by the construction environment, strong adaptability and extremely low failure rate. If large production is required, multiple units can be assembled.

After the emulsified bitumen equipment has been used for a long time, it needs maintenance. There are several points to note when adjusting the emulsified bitumen equipment:
1. During use, regular maintenance should be carried out as appropriate according to the processing materials;
2. For the maintenance and use of the motor, please refer to the motor manual;
3. Most of the random spare parts are national standard and department standard parts, which are purchased all over the country;
4. The colloid mill is a high-precision machine with a line speed of up to 20m/second and a very small grinding disc gap. After inspection and reinstallation, the coaxiality error between the housing and the main shaft must be corrected with a dial indicator ≤0.05mm;
5. When repairing the machine, it is not allowed to be directly knocked with an iron bell during the disassembly, reinstallation and adjustment process. Use a wooden hammer or a wooden block to knock gently to avoid damaging the parts;
6. The machine seals: divided into static and dynamic seals. The static seal uses an O-type rubber ring and the dynamic seal uses a hard mechanical combined seal. If the hard sealing surface is scratched, it should be repaired by grinding on flat glass or flat casting immediately. The grinding material should be ≥200# silicon carbide grinding paste. If the seal is damaged or cracked seriously, please replace it immediately.

Bitumen decanter equipment can be placed in a complex system as an independent unit, replacing the existing heat source de-barreling method, or in parallel as a core component of a large set of equipment, or it can work independently to meet the requirements of small-scale construction operations.
The Sinoroader bitumen decanter device is mainly composed of a de-barreling box, a lifting mechanism, a hydraulic thruster and an electrical control system. The box is divided into two chambers, the upper chamber is a barreled bitumen melting chamber, and heating coils are evenly distributed around it. The heating pipe and the bitumen barrel mainly exchange heat in a radiation manner to achieve the purpose of bitumen de-barreling. Several guide rails are the tracks for the bitumen barrel to enter. The lower chamber is mainly to continue heating the bitumen removed from the barrel to make the temperature reach the suction pump temperature (100℃), and then the asphalt pump is pumped into the upper chamber. At the same time, an empty barrel is pushed out at the rear end outlet. There is also an oil tank on the platform at the entrance of the asphalt barrel to prevent the dripping bitumen from flowing out.
The inlet and outlet doors of the device adopt a spring automatic closing mechanism. The door can be automatically closed after the asphalt barrel is pushed in or out to reduce heat loss. A temperature gauge is installed at the asphalt outlet to observe the asphalt outlet temperature. The electrical control system can control the opening and closing of the hydraulic pump and the reversing of the electromagnetic reversing valve to realize the advance and retreat of the hydraulic cylinder. If the heating time is extended, a higher temperature can be obtained. The lifting mechanism adopts a cantilever structure. The bitumen barrel is lifted by an electric hoist, and then moved horizontally to place the bitumen barrel on the guide rail. A temperature gauge is installed at the outlet of the asphalt meltering equipment to observe its outlet temperature.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

Emulsified asphalt equipment improves the fluidity of asphalt: When the emulsified asphalt equipment is subjected to mechanical actions such as high-speed centrifugation, shearing, and impact, the emulsified asphalt equipment makes it into particles with a particle size of 0.1~5μm, and disperses it into a water medium containing a surfactant (emulsifier-stabilizer). Since the emulsifier can be directional adsorbed on the surface of the emulsified asphalt equipment particles, the interfacial tension between water and asphalt is reduced, so that the asphalt particles can form a stable dispersion system in water. The emulsified asphalt equipment is an oil-in-water emulsion.

In the asphalt-water system, the emulsifier molecules move between the asphalt and water interface, and the water-loving groups of the molecules are adsorbed on the surface of the asphalt, making it charged, while the hydrophilic groups enter the water phase. This connects the asphalt particles with water, reducing the interfacial tension between the two. At the same time, because the asphalt particles have the same charge and repel each other, they are prevented from agglomerating with each other, so that the asphalt emulsion can remain uniform and stable for a certain period of time. The nature of the charge is determined by the charge of the hydrophobic group or hydrocarbon chain of the emulsifier. If it is negatively charged, the asphalt particles are negatively charged, and the emulsion formed is an anionic asphalt emulsion. Otherwise, it is a cationic asphalt emulsion. If the asphalt particles have both negative and positive charges, the emulsion is a zwitterionic asphalt emulsion; in addition, there is also a non-ionic asphalt liquid.

As a black road construction machinery, the synchronous chip sealer is the main equipment for highways, urban roads, airports, and port terminal facilities. Do you know what kind of synchronous chip sealer? What products do you have to choose from?
Asphalt dispensers are classified according to the purpose, operation mode, and drive mode of the asphalt pump. According to the purpose, asphalt dispensers can be divided into two types: road use and road construction use. The asphalt tank capacity of the asphalt dispenser used for road construction generally does not exceed 400L, while the asphalt tank capacity of the asphalt dispenser used for road construction is 3000-20000L.

The hydraulic bitumen decanter equipment produced by our company uses thermal oil as the heat carrier and has its own burner for heating. The thermal oil heats, melts, debarks and dehydrates the asphalt through the heating coil. This device can ensure that the asphalt does not age, and has the advantages of high thermal efficiency, fast barrel loading/unloading speed, improved labor intensity, and reduced environmental pollution.

With reliable performance and stable benchmark quality, Sinoroader slurry sealer is favored by customers and was once in short supply. Sinoroader slurry sealer uses emulsified asphalt, which can reduce the sensitivity of construction temperature and effectively extend the construction time. Sinoroader slurry sealer has fast molding, improves construction speed, shortens road construction time, and reduces the manpower and material resources required for construction. In addition, in terms of energy saving and consumption reduction, Sinoroader slurry sealer can be constructed at room temperature, achieving “0 release” of harmful gases, reducing air pollution, and is very green and environmentally friendly.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

Regarding the basic knowledge of modified bitumen plant, I believe that many consumers have already had a basic understanding of it. Because of the continuous development of various fields today, various facilities including modified bitumen plants have been well developed and applied, and modified bitumen plant has gradually been recognized by customers.
The direct quick heating portable equipment in the modified bitumen equipment not only has a faster heating speed, saves fuel, and is pollution-free, but also convenient and easy to operate. The automatic heating system completely eliminates the trouble of baking or cleaning bitumen and pipelines.

Modified asphalt equipment is a widely used asphalt equipment. Now its ultra-high performance has been widely praised by users. However, we must first ensure the safe use of modified asphalt equipment in order to fully demonstrate its performance. So how much do you know about the safe use and operation of modified asphalt equipment? Today, Gaoyuan Road Construction will explain it in detail:
1. Placement: The modified asphalt equipment should be placed on a flat place, and the front axle wheel should be fixed with sleepers and the tires should be suspended to ensure that the machine does not move around during operation.
2. Check regularly whether the mixer blades are deformed and whether the screws are loose.
3. Check whether the running direction of the mixing barrel is consistent with the arrow. If not, please replace the positive and negative poles of the wiring.
4. Before powering on, check for empty vehicle trial operation, check for leakage, and check the idling of the mixing barrel. The normal speed is about 3 times faster when the empty vehicle is full. If the speed is wrong, you should stop and check.
5. If the machine is stopped for more than one hour after the asphalt mixing is completed, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water accumulation in the barrel to prevent the formula from changing and even rusting of the pages and other links.

From the current point of view, road construction machinery has bottomed out and asphalt meltering equipment has risen rapidly. In recent years, highway construction and maintenance departments have a strong awareness of using asphalt mixing equipment, especially in developed coastal areas such as Beijing, Shanghai, Jiangsu, Zhejiang, etc. In addition, these regions have a fast economic growth rate, relatively developed industry, and strong comprehensive economic strength. Therefore, the consumption of asphalt mixing equipments in these regions has always been at the forefront of the country. With the rapid development of highway construction and the increase in demand for asphalt, barreled asphalt has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported asphalt used in high-grade highways is in barrel form, which requires an asphalt meltering equipment with fast melting speed, clean de-barreling, and can prevent asphalt aging. my country’s highway construction has achieved remarkable results, among which mechanized production has contributed greatly. Different types of asphalt mixers and bitumen meltering equipment are selected for the characteristics of large highway pavement construction and tight construction period. With the rapid development of my country’s economy, the further extension of expressways, and the large-scale development of western construction, the central and western regions have become new investment hotspots. While paying attention to the market in the developed eastern regions, domestic road construction machinery manufacturers have also increased their efforts to develop the central and western markets, creating new highlights for the domestic asphalt mixing plants consumer market. In summary, my country’s asphalt mixing plant sales market has begun to move westward with the westward movement of investment hotspots. As the market center of gravity gradually shifts westward, the market in the western region is gradually heating up. The self-heating integrated structure, hot air barrel melting and bitumen barrel flipping technology in the asphalt barrel removal equipment are our company’s self-heating integrated structure. The thermal oil furnace used in the old equipment is perfectly integrated with the asphalt barrel removal equipment body, which reduces the volume of the entire set of equipment, greatly reduces equipment investment, saves equipment space and transfer transportation costs.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

There are many types of emulsified bitumen, and PC-2 is one of them, which is a spray-type emulsified bitumen. It is used for spraying oil through the base layer of granular materials and health care spraying on semi-rigid base layers. There is also the PA-2 type, which has the same purpose as the PC-2 type. The difference is that the PC-2 type is a cation, while the PA-2 type is an anion.

Synchronized gravel sealing is a process technology for treating cracks in asphalt pavement, and it is currently a road construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical features are? If you don’t know, just follow the editor of Sinoroader and take a look.

What details should be paid attention to when adding materials to the emulsified bitumen equipment? Speaking of emulsified bitumen equipment, I don’t know how much you know? What should we pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified bitumen equipment has no heating barrel. Before use, you must first add an appropriate amount of diesel, let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is about 80 to 100 degrees) Open the shut-off valve on the oil pipe and discharge the diesel in the machine. The temperature of the black anti-static tweezers grinding wheel is about 80 to 100 degrees before it can be loaded and put into production. If there is a heating collet, heat the grinding wheel before starting, and then load the materials for production.