What are the common hardware failures of asphalt mixing plants?

Asphalt mixing station is one of the most important equipment in processing operations, so how to build a website has become the focus of people’s attention. The editor has compiled some key points, hoping to be helpful to everyone.

The first step in establishing an asphalt mixing station is to determine the host machine and feed batching system. Generally, the configuration is based on the project’s construction period, total amount of concrete, daily concrete consumption and other indicators. The basic principle is to meet the daily concrete consumption. Under normal circumstances, a project can only have one asphalt mixing station, or separate mixing stations can be set up according to zones, or a large mixing station can be set up together with an appropriate number of concrete transport trucks, all of which depend on the actual situation.

In general, the development of my country’s asphalt mixing plant industry is very rapid. In the ton segment, it quickly occupied most of the market share. And with the advancement of technology, it can basically meet the current development needs. However, the total demand for some large-scale asphalt mixing plants has not increased or decreased. What are the reasons?
If we analyze from multiple angles, it is not difficult to find that these reasons are also some of the problems faced by my country’s current asphalt mixing plantindustry. These problems are summarized as follows:

Asphalt mixing equipment has a special function, which is that it can perform cyclic heating to make the asphalt product reach the best condition. But how does it achieve this function? Everyone is curious about this.

There is also a reversing valve in the asphalt mixing plant, which generally does not cause problems, so I have not understood its solutions in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?
The failure of the reversing valve of the asphalt mixing station is not complicated, that is, the reversing is not timely, gas leakage, electromagnetic pilot valve failure, etc. The corresponding causes and solutions are of course different. For the reversing valve to not change direction in time, it is generally caused by poor lubrication, the spring is stuck or damaged, oil dirt or impurities get stuck in the sliding part, etc. For this, it is necessary to check the status of the lubricator and the quality of the lubricating oil. Viscosity, if necessary, the lubricant or other parts can be replaced.
After long-term use, the reversing valve is prone to wear of the valve core sealing ring, damage to the valve stem and valve seat, resulting in gas leakage in the valve. At this time, the sealing ring, valve stem and valve seat should be replaced, or the reversing valve should be replaced directly. In order to reduce the failure rate of asphalt mixers, maintenance must be strengthened on a daily basis.

Asphalt mixing plant equipment is mainly composed of batching system, drying system, ignition system, hot material lifting, vibrating screen, hot material storage bin, weighing mixing system, asphalt supply system, granular material supply system, dust removal system, finished product hopper and automatic control system.
Components:
⑴ Grading machine
⑵ Vibrating screen
⑶ Belt vibrating feeder
⑷ Granular material belt conveyor
⑸ Drying mixing drum;
⑹ Coal powder burner
⑺ Dust removal equipment
⑻ Bucket elevator
⑼ Finished product hopper
⑽ Asphalt supply system;
⑾ Distribution station
⑿ Automatic control system.

People pay more and more attention to urban construction, and the use of asphalt is increasing. The application rate of asphalt mixing station is naturally growing rapidly.
Asphalt mixing station will encounter some faults more or less during use. The most common ones are uneven wear of the supporting wheel and wheel rail. Sometimes there will be some abnormal noise and gnawing. The main reason for this is that after the asphalt mixing station has been working for a period of time, the internal drying cylinder will be subjected to high temperature, and then friction will occur between the supporting wheel and wheel rail.
The above situation will also be accompanied by severe shaking, because the asphalt mixing station will directly cause the gap between the wheel rail and the supporting wheel to be improperly adjusted under the action of the drying material, or the mutual position of the two will be skewed. When encountering this situation, the user should add grease to the surface contact position of the supporting wheel and the wheel rail after daily operation.
In addition, the staff also need to pay attention to and timely adjust the tightness of the fixing nut while adding grease, and then effectively adjust the spacing between the supporting wheel and the wheel rail, so that the asphalt mixing station can work smoothly, all contact points can be evenly stressed, and there will be no shaking.

In highway construction, asphalt mixing station plays a vital role. As a kind of equipment integrating intelligence, high efficiency and environmental protection, asphalt mixing station provides strong support for improving the quality of highway construction. This article will introduce the relevant knowledge of asphalt mixing station in detail to help readers understand this key equipment.
Asphalt mixing station is a kind of equipment specially used for producing asphalt concrete, which is widely used in highway, municipal road, bridge and other engineering construction. Asphalt concrete is a kind of building material mixed with asphalt, gravel, sand and other materials. It has the characteristics of strong durability and good compressive resistance. It is an ideal material for highway construction.
2. Features
Intelligence: Asphalt mixing station is equipped with advanced control system and sensor, which can realize automatic production, reduce manpower input and improve production efficiency.
Environmental protection: Asphalt mixing station adopts closed design to reduce dust pollution, and is equipped with noise reduction facilities to reduce noise pollution.
Efficiency: Asphalt mixing station has high production capacity and can produce a large amount of asphalt concrete in a short time to meet the needs of engineering construction.
3. Function
Provide asphalt concrete: The main function of asphalt mixing station is to produce asphalt concrete and provide necessary building materials for highway construction.
Improve highway quality: By using asphalt concrete, the smoothness, compressive strength and durability of the highway can be improved, thereby improving the quality of the highway.

Asphalt mixing stations and equipment must implement secondary leakage protection measures. They can only be used after being plugged in and operated through the circuit breaker before use. During the trial operation, it is necessary to verify that the rotational speed of the mixing drum will be inappropriate.

Many people think that since both asphalt mixing plants and asphalt mixing plants are equipment for producing asphalt, there should be no difference between them, even if there is, it is only in appearance and volume. However, asphalt mixing plants and asphalt mixing plants are different in even their basic structure and function.
First, let me introduce the basic structure of an asphalt mixing plant, which includes five major components: material supply system, metering system, mixing system, and electrical control system. In comparison, the structure of an asphalt mixing plant is simpler, without so many components, so its operation and maintenance will be simpler.

Asphalt mixing plant is a complete set of equipment composed of many systems. It is widely used in the current society. Its components include batching system, drying system, combustion system, hot material lifting, weighing and mixing system and control system.
In the process of asphalt mixing, heating is an indispensable link, because there must be a system for heating in the asphalt mixing station, but the system generally fails for various reasons. So how should the heating system of the asphalt mixing station be improved? This article will briefly explain this issue.
Generally speaking, when the asphalt mixing station is running under low temperature conditions, the asphalt circulation pump and spray pump cannot operate normally, which will cause the asphalt in the asphalt scale to solidify, and then the asphalt mixing station cannot be produced. Therefore, the asphalt mixing station needs a heating system during operation.

At present, the production efficiency of asphalt mixing plants in my country’s asphalt construction is far lower than the theoretical efficiency at the time of design. The low efficiency of organic waste gas treatment will not only delay the construction process and cause a waste of resources, but also the quality of the construction will not be very good. guarantee. In the construction of asphalt pavement, the main reasons for the low production efficiency of the asphalt plant are insufficient supply of mixture, resulting in loss of continuity of construction, improper equipment parameter settings, excessive overflow and other problems. Effective measures must be taken to deal with these problems, and ultimately improve production efficiency and ensure construction quality.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

Asphalt mixing plant, also known as asphalt concrete mixing plant, is a complete set of equipment for batch production of asphalt concrete. Its efficient and stable operation is of great significance to ensure the quality of the project. It is mainly used in the construction of highways, grade roads, municipal roads, airports, ports and other projects. According to the mixing method, asphalt mixing plant can be divided into forced intermittent type and continuous production type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.
The working principle of asphalt mixing plant mainly includes steps such as aggregate processing, asphalt processing and mixture mixing. Specifically, aggregates (such as gravel, crushed stone, etc.) are sent to aggregate bins through conveyors or bucket elevators, and then measured by aggregate metering devices, and a certain amount of aggregates are sent to sub-bins. Asphalt is stored in asphalt bins or oil storage tanks, and is measured by asphalt metering devices, and a certain amount of asphalt is sent to asphalt sub-bins. Finally, according to the ratio requirements, different aggregates are taken out from their respective sub-bins and sent to the mixture mixer through conveyors or bucket elevators for mixing.

The development prospects of asphalt mixing plants are very good, and the product competition on the market is also very fierce. When the equipment is used, uneven wear of the supporting wheels and wheel rails often occurs, and sometimes there are some abnormal noises and edge gnawing. The main reason is that after the asphalt mixing station has been working for a period of time, the drying cylinder is exposed to high temperature and friction occurs between the supporting wheel and the wheel rail.
Under the action of drying materials in an asphalt mixing station, the equipment will vibrate violently, which will directly lead to improper adjustment of the gap between the wheel rail and the supporting wheel, or mutual interference between the two. The position is skewed, so the operator needs to add grease to the surface contact positions of the supporting wheel and the calibrating wheel rail after every day’s work.

1. Small asphalt mixing equipment should be set on a flat ground, and the front and rear wheel axles should be padded with square wood to fix the overhead tires to prevent sliding during use.
2. Check whether the transmission clutch and brake are sensitive and reliable, whether the connecting components are worn, whether the track pulley is outstanding, whether there are obstacles around and the smoothness of each part.
3. The rotation direction of the mixing drum should be consistent with the direction indicated by the arrow. If not, the motor wiring should be corrected.
4. Small asphalt mixing equipment should implement secondary leakage protection measures. Before use, the power should be turned on and the empty vehicle operation is qualified before it can be officially used. During the trial operation, the mixing drum speed should be checked to see if it is appropriate. Under normal circumstances, the empty vehicle speed is slightly faster than the heavy vehicle (after loading) by 2-3 revolutions. If the difference is large, the ratio of the driving wheel to the transmission wheel should be adjusted.
5. When stopping use, the power should be turned off and the switch box should be locked to prevent others from operating it by mistake.
6. When the concrete mixing is finished or it is expected to stop for more than 1 hour, in addition to draining the remaining material, pour stones and clean water into the shaking barrel, start the machine and run it, rinse the mortar stuck on the barrel and unload it completely. There should be no water accumulation in the barrel to prevent the barrel and blades from rusting. At the same time, the dust outside the mixing barrel should be cleaned to keep the machine clean and intact.
7. After starting the machine, always pay attention to whether the operation of each part of the mixer is normal. When stopping the machine, always check whether the mixer blades are bent and whether the screws are knocked off or loose.

The actual operation steps of drying drum of asphalt mixing equipment: 1. Pay attention to routine inspection; 2. Proper operation steps; 3. Effective maintenance.
Drying drum is a cylindrical device specially used for heating and drying stones in asphalt mixing equipment. Proper application and maintenance of drying drum can maximize the performance of drying drum, increase its service life and reduce application cost. Let’s take a look at the actual operation steps below.
1. Pay attention to routine inspections
The asphalt mixing equipment drying drum has been tested and inspected before leaving the factory, but it will be subjected to vibration and vibration during transportation to the construction site. A comprehensive inspection should be carried out before use: check whether all anchor bolts are tightened; whether all key pins are properly driven; whether all drive devices are adjusted according to the manufacturer’s instructions; whether all pipe connections are appropriate and whether the three-way joints are reliable; whether the entire equipment is fully lubricated; start the motor and check whether all parts can rotate steadily in the correct rotation direction; whether the pressure gauge can work normally and whether the valve is adjusted to the correct working pressure; whether the burner ignition mechanism is available and whether the gate valve is open.
2. Correct operation steps
After the equipment is started, it is recommended to control the machine manually at the beginning, and then switch to the automatic control mode after achieving the required production volume and pouring temperature. The stone should be dried and have a stable moisture content as much as possible so that the stone can maintain a stable final temperature when passing through the drying drum. If the stones delivered to the drying drum change frequently and the moisture content changes each time, the burner should be adjusted frequently to compensate for these changes.
The stones directly from the crushed stone have a relatively constant moisture content, while the stones from the outdoor storage yard have a higher moisture content, and the moisture content of different piles varies greatly. Therefore, it is best for the stones to come from the same source.

Construction safety has always been a major issue, and we cannot let any safety hazard go unnoticed. Especially the use of equipment at the construction site. Asphalt mixing stations are prone to failure. Strengthening the maintenance of this equipment is essential to ensure safe construction at the construction site, improve equipment integrity, reduce equipment failures, and ensure the quality of concrete. The role of neglect.
The composition of the asphalt mixing plant is relatively complex, so during maintenance, classified maintenance should be carried out according to the usage and functions of different parts. Maintenance content can be divided into tank maintenance, winch system maintenance and adjustment, stroke limiter adjustment and maintenance, wire rope and pulley maintenance, lifting hopper maintenance, track and track bracket maintenance, etc.

The asphalt mixing plant is a complete set of equipment for mass production of asphalt concrete. The whole machine of the equipment consists of multiple systems, such as batching system, drying system, combustion system, powder supply system and dust prevention system. Each system is an important part of the asphalt mixing plant.
The working condition of the combustion system of the asphalt mixing plant has a great impact on the whole system, which is related to the economic efficiency of the whole system, temperature control accuracy and flue gas emission indicators. This article will briefly introduce how to judge the working condition of the combustion system of the asphalt mixing plant.
Generally speaking, due to the complexity of the detection equipment and methods, there are no conditions to achieve in the working process of most asphalt mixing plants. Therefore, it is more convenient to judge the working condition by a series of relatively intuitive factors such as the color, brightness and shape of the flame. This method is very simple and effective.

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

Asphalt mixing plants are large-scale products with high professional and technical requirements, and are composed of multiple systems. Among them, asphalt tanks are also a very critical part. Whether it is manufacturing, debugging or installation, it needs to be operated according to the actual application needs of users.
In addition to the manufacturing, debugging and installation, which need to be operated by installers, the maintenance of asphalt tanks in asphalt mixing plants must also be managed by professionals. At the same time, they must strictly follow all safety rules to operate. Before operation, they must be proficient in the relevant requirements and based on the regulations and safety instructions for storing and handling hot asphalt.

The application of asphalt mixing plants also involves selection issues. In order to give full play to the performance of the equipment, the model of the machine is mainly determined according to the actual situation of the construction site. It sounds relatively simple, but some details still need to be emphasized.
The so-called specific conditions of the construction site first include the size of the site; secondly, the properties, specifications and working dimensions of the enterprise’s supporting equipment. It is necessary to try to do a good job in all aspects to help improve production efficiency and ensure product quality. In the case of intensive network management, the network management function of the asphalt mixing plant must also be taken into account to avoid difficulties in future upgrades.

Determining the material is a necessary stage in the design process of asphalt mixing equipment, and it is also one of the most critical links, because the material will be directly related to the use effect and service life of the entire equipment. Generally, when we determine the machine material, we usually base it on the characteristics of the working medium, and the same is certainly true for asphalt mixing equipment.

Due to the good reliability of asphalt, more and more fields have just begun to use asphalt as raw material for daily production and processing work; such as construction, urban roads, etc. In addition, the processing plant will humanize and manufacture asphalt according to customer requirements, and will use professional technical tools for asphalt mixing work. Compared with the application of old technical equipment, the new asphalt mixing equipment has stronger technicality and efficient operation speed. In addition, the equipment will use an automatic computer operating system to reduce redundant errors and reduce the working time of operators.
In addition, the processing plant will also mix and manufacture asphalt with higher precision asphalt mixing equipment, and only a small amount of raw materials and natural materials will be used for asphalt mixing and manufacturing; and it can reasonably control the quality of goods and improve the quality of goods.
Do you master the whole process of asphalt mixing equipment? The whole working process is a fusion of stone mixing, slag micro powder mixing and asphalt mixing. You can find a lot of detailed information below.

If you look at an asphalt mixing plant from a professional perspective, do you know how to judge its work and significance? In fact, the so-called asphalt mixing station is the one that produces asphalt. We can usually see it in road construction projects. Specifically, it mixes some materials that need to be used during the construction process according to certain proportion requirements. Then complete the corresponding construction work.
Then, we can analyze it from a market perspective. Since it was used in the market, it has been widely praised by users. Today’s asphalt mixing plant technology has been greatly improved, and the entire set of equipment used has a variety of advantages. , such as meeting the requirements of stable control, screening, efficient dust removal, excellent mixing, and green environmental protection during the work process. It is even more obvious when used in large-scale projects such as high-grade highways and airports.

Effective maintenance of the drying drum of the asphalt mixing plant can extend its service life and reduce the cost of use. Let’s take a look at how to maintain it reasonably.
1. The drying drum should be stopped when the aggregate is not running in the asphalt mixing equipment. After the work is over every day, the equipment should be operated to discharge the aggregate into the dryer. After closing the combustion chamber, the combustion chamber should be idle for about 30 minutes to cool down to reduce the impact or allow the machine to run automatically.
2. Install the drying cylinder fixing ring on the roller synchronously. Check the environment in the patrol ring regularly. Whether the roller is adjusted, the straight roller will automatically move to the conveying end, and then the bias will be adjusted to the correct position.
3. If the roller table is in contact with only one of the two thrust rollers, the gap sheet can be filled under the support roller until it is simultaneously subjected to the full width of the support ring. The specified nutritional state should be maintained by the thrust wheel, but it is used to compensate for the desire not to express.
4. If the drying drum is equipped with a drive device, a certain amount of power should be added in small amounts.

The materials used in asphalt mixtures contain a lot of dust. When the equipment is operating, if the dust enters the atmosphere, it will cause pollution. Therefore, dust removal equipment must be installed, and now bag dust removal is the main method. Safety is a common sense issue. There are well-established standard safety rules.
Do not clean, oil or adjust any mechanical equipment that is not specifically explained during operation; turn off the power and lock it before inspection or repair activities to prepare for accidents. Because each situation has its own particularity. Therefore, be vigilant about safety damage issues, incorrect operation issues and other deficiencies. All of them may lead to accidents, personal injuries, reduced production efficiency, and more importantly, loss of life. Careful and early prevention is the best way to avoid accidents.
Careful and correct maintenance can make the equipment work more efficiently and control it within a certain level of pollution; the maintenance of each component should be carried out according to its operating standards; maintenance plans and safe operation procedures should be formulated according to the inspection and repair conditions that must be carried out.
Take out a work log to record all inspection and repair conditions, list the analysis of each inspection of each component and the description of the repair content or the date of the repair; the second step is to give the inspection cycle for each component, which should be determined according to the service life and wear condition of each component.

Speaking of asphalt mixing plants, we are not unfamiliar with them. This is a unit equipment specially used for asphalt mixing. In fact, what we really lack understanding of is its gas system. Even the accumulated failures that often occur in the gas system of asphalt mixing plants are not very clear. Facts have proved that only by properly maintaining the various systems of the equipment can efficient production and good benefits be achieved.
The following are four types of gas system failures that often occur in asphalt mixing plants. Let’s analyze the causes of the problems behind the failures one by one.

Any kind of mechanical equipment must go through precise design, testing and other processes before it can be manufactured, and the same is true for asphalt mixing stations. According to the survey, the following stages are necessary for any asphalt mixing plant.
First of all, the main technical parameters of the product to be designed must be determined according to market needs, so construction market research, data analysis and other links are indispensable. Secondly, the ideal working principle and the plan to realize this principle will be determined through innovative conception and optimization screening. , a schematic diagram of the overall design scheme should also be given.